Question about 1999 Toyota Camry

1 Answer

Car stops in idle position

It stops also when u use steering too mich

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 76,649 Answers

This can be caused by a dirty automatic idle speed control valve and throttle valve on the engine. Do the following to correct the problem.
Buy a can of throttle valve cleaner (it is made by CRC) from the local auto parts store, NEVER USE CARB CLEANING SPRAY, IT DESTROYS THE ANTI-STICK TEFLON COATING, spray it into the air intake through the throttle body of the engine until you have used about half the can, you will need to hold the idle up while you do this, it will try to stall, after this shut the engine down and disconnect the Negative (-) battery cable for 5 minutes. The intake is now clean, if you continue to have the idle speed control problems you may need to seek the help of a professional

Posted on Feb 14, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Checking and replacing power steering fluid


1. Open the hood of the vehicle.

2. Look for the power steering fluid reservoir.

3. Raise the reservoir and disconnect the hose that goes to the oil cooler.

4. Connect a hose of suitable diameter to the disconnected hose that goes to the oil cooler and put the hose end in the fluid jar.( be careful not to spill the fluid on the painted area of the body. Wipe off spilled fluid at once.)

5. Start engine and let it run at idle. Turn the steering wheel from lock to lock position several times. When fluid stop running out from the hose, shut off the engine. Discard fluid that was drained from the reservoir.

6. Re-fit the return hose to the reservoir.

7. Fill the reservoir to the level mark.

Note: Use only fluid that is recommended by the manufacturer.

8, Start engine and run it at fast idle. Turn the steering wheel from lock to lock position several times in order to bleed air that is present inside the system.

9. Recheck the fluid level. Add some if necessary.

Note: Do not fill the reservoir beyond the upper limit

on May 14, 2010 | Toyota Corolla Cars & Trucks

1 Answer

The steering of my car vibrates with the car stopped. Some body help to solve this problem? Its make me crazy. With the car stopped (N neutral position) when I speed (over a thousand turns) and loose the...


Probably the wrong place to be asking this question. If you don't have knowledge of the workings of any vehicle, then you need to find repair shop. If you have friend that works in repair shop, ask him. It sounds to me that you have lose fitting or knuckle where the rod attaches to gear box. It definitely needs to be check as soon as possible before you lose your steering.

Feb 04, 2015 | Nissan Cars & Trucks

1 Answer

Why is my steering wheel hard after i rebuilt the power steering pump of a dodge durango 1999 5.9L SLT 4X4. It is filled up with oil i already turned it on above idle position.


if you rebuilt could be you reversed some kind of valve...or you could have air in system (there is a certain eay to bleed air out of the steering system on the newer cars...like all the way left,all the way right ....or you might have accidently used the wrong power steering fluid ....cars are picky these days ...we used to use automatic trans fluid in the old days....not anymore!.... the fluid bubbles, i did this in a `85 dodge van and thought the front wheels would fall off when going down the road...

Feb 21, 2014 | Dodge Durango Cars & Trucks

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

1 Answer

Need to replace power steering pump


if you leave in Michigan you can get a used on at LKQ in Grand Rapids Mich Phone 616-877-3490 its self serve for around $25.00 if you do not leave give this website a try to find a good salvage yard near you www.junkyarddog.com wish you the best of luck Michigan Man.

Aug 21, 2010 | 1993 Plymouth Voyager

1 Answer

When bought engine idled @ 800 rpm when warm, now engine lite is on and engine idles rough @ 500 to 600 RPM. Replaced rack and pinion, power steering, checked wires, replaced sparkplugs, # 1 plug was in...


could be numerous reasons. this is your best bet take it in to a mechanic and have your engine codes scanned. it is a minimal charge, some even do it for nothing it only takes 10 minutes.this will point you in the right direction.

Jan 27, 2010 | 2000 Ford Windstar

1 Answer

How to adjust idle on ford falcon el 6 cylinder


wam the car up, disconnect the idle speed control valve wiring plug (idle control valve sits on top of the throttle body) then set the idle to 700rpm with the grub screw stop just above where the throttle cable fits to the throttle body. Reconnect theidle control valve and you're done. It may take a few k's driving for the ECU to relearn the new throttle stop position. The idle speed control valve is only used by the ECU to add idle speed when extra load is put onto the engine such as power steering or air con use, the base idle is set mechanically on the old falconns.

Oct 04, 2009 | 1983 Ford Fairmont

3 Answers

2003 expedition replaced p/s pump and steering rack. it is still hard to initiate a turn in either direction regardless of speed


raise the truck up and turn the wheels left to right, you most likely have air in the lines.

Sep 28, 2009 | 2003 Ford Expedition

1 Answer

2000 Hyundai starts and then stops immediately.


the fuel pump relay is under the steering wheel by the computer..... lay under the steering wheel and its on the left of the steering wheel.

Feb 19, 2009 | 2000 Hyundai Accent

Not finding what you are looking for?
1999 Toyota Camry Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...