Question about Cars & Trucks

Open Question

How to remove rear seat from Mazda protege5 - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pippall
  • 1486 Answers

SOURCE: I have a 2003 Mazda Protege5. I am changing the

by pushing and turning at the same time.Turn clock wise and push.You can by a tool to do this.But it can be done uesing a pipe grips to turn and push at the same time.Good luck

Posted on Sep 15, 2009

Testimonial: "Thanks for the help! I've had cars that push back, I've had cars that turn, now I have both. Thank you very much!!"

  • 7 Answers

SOURCE: rear view mirror

Has the mirror previously been capable of providing a view of the left lane?
If it did not, the "clicking" sound is simply an indicator informing the user that the angle limit has been reached, the mirror will not travel any further.
Simply purchase a pair of stick on Convex mirrors, they are about 1.5" in diameter,they do the job perfectly. I know this because I've got them on my Protege5 mirrors.

Posted on Sep 26, 2009

  • 7353 Answers

SOURCE: 2003 mazda protege5 how do you collasp rear brake

Turn it to the right as you are pushing it in.

Posted on Feb 06, 2010

  • 18 Answers

SOURCE: how would i remove a left door panel on my mazda

If its a front door, you need to pop off the little panel inside of the mirror area. The there are several plastic clips that you pop out with screwdriver. There may be one with a philips head that can be unscrewed. Next you remove 2 or 3 screws from the door handle. Door handle has one side (usually front) that pops out first after screws are out. There may be 2 more screws under door handle if its a front door, not on rear door. Then you use a large screwdriver and pop out bottom sections of door and slide panel up to release the 2 locator pins on the top side of the door panel. These instructions are for 2001 Protege so it should be same for your car.

Posted on Jun 29, 2010

  • 1915 Answers

SOURCE: How do you remove the back seat on a 1998 Mazda

push HARD on the bottom of the bottom seat at the lower front point by the floor (one side at a time) and lift-once you release both sides, it just pulls out.

Posted on Dec 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1250 and P1569 codes. Engine still running rough after complete tuneup. What should I check now. Any Mcguyver fixes? 2002 Mazda Protege5


1250 is the fuel pressure regulator and 1569 is variable timing control solenoid. Both will cause rough running. I would check the regulator out first.

Dec 27, 2016 | 2002 Mazda Protege5

2 Answers

Replace fuel pump


Kev, Depends on year make and model, some have access by removing rear seat and then a access hatch, or in trunk hatch, which will allow pump removal with out dropping fuel tank. Google your year,make and model fuel pump replacement. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Removing An Old Fuel Pump
Mazda Protege5 Protege Familia Fuel pump sending unit repla
How to change fuel pump Toyota Corolla VVTi engine Years 2000 to 2015


Jul 03, 2016 | Cars & Trucks

1 Answer

Were is the knock sensor on 2002 protege5 2.0L


The knock sensor is located under the intake manifold to replace do the following
Disconnect the negative battery cable.
Remove the intake manifold.
Disconnect the sensor connector.
Remove the sensor from the engine block.
Installation is the reverse of the removal procedure

Sep 28, 2012 | 2002 Mazda Protege

1 Answer

Mazda protege5 timing belt2003


Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams for use.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2003/make/mazda/model/protege5/2003_mazda_protege5_timing_belt_diagram_marks.htm

Mar 22, 2010 | 2003 Mazda Protege

1 Answer

How would i remove a left door panel on my mazda protege5?


If its a front door, you need to pop off the little panel inside of the mirror area. The there are several plastic clips that you pop out with screwdriver. There may be one with a philips head that can be unscrewed. Next you remove 2 or 3 screws from the door handle. Door handle has one side (usually front) that pops out first after screws are out. There may be 2 more screws under door handle if its a front door, not on rear door. Then you use a large screwdriver and pop out bottom sections of door and slide panel up to release the 2 locator pins on the top side of the door panel. These instructions are for 2001 Protege so it should be same for your car.

Mar 07, 2010 | 2002 Mazda Protege

1 Answer

Rear view mirror


Has the mirror previously been capable of providing a view of the left lane?
If it did not, the "clicking" sound is simply an indicator informing the user that the angle limit has been reached, the mirror will not travel any further.
Simply purchase a pair of stick on Convex mirrors, they are about 1.5" in diameter,they do the job perfectly. I know this because I've got them on my Protege5 mirrors.

Sep 22, 2009 | 2002 Mazda Protege

1 Answer

I have a 2003 Mazda Protege5. I am changing the


by pushing and turning at the same time.Turn clock wise and push.You can by a tool to do this.But it can be done uesing a pipe grips to turn and push at the same time.Good luck

Sep 15, 2009 | 2002 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...