Question about Cars & Trucks

Open Question

How do you bleed clutch on 06 hiace

Cannot get any pressure at slave

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1056 Answers

SOURCE: replaced clutch slave cylinder blew

Could be a couple of different things.
1) your clutch master has a plugged pressure bypass, and it is sending excessive pressure to the slave and blowing it out.
2) The clutch throw out arm is bound, and will not allow the slave to compress it.
3) The replacement slave was defective.

What was the reason for replacing the slave in the first place?

Posted on Jul 31, 2008

  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

  • 1 Answer

SOURCE: 1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Posted on Aug 01, 2009

  • 1 Answer

SOURCE: New clutch won't work.

I too have a 2003 Ranger and am on my second clutch, master clyinder and slave cylinder at 90k miles. Assuming all parts are installed correctly I would check the slave cylinder next to the master in engine compartment--it is the small plastic resevoir. Don't bother trying to bleed as you are wasting your time. Remove rubber boot after removing cap and you will probably find a lack of fluid or dirt in bottom. It has a one way valve and once you **** in dirt and air it's all over. It comes primed with fluid from the factory--I belive the part is made in France. Also when you remove you will have to break plastic washer under dash which is worth about $.02, but Ford charges around $30--it connects linkage with master cylinder. Replace master and the washer and you will probably have clutch pedal and be able to engage gears.

Posted on Dec 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 s 10 clutch wont catch after bleeding it replaced masre and slave clutch


Are you sure all the air is out of the system and you have a firm pedal feel. If not have a shop pressure bleed the clutch hydraulic system.

Apr 21, 2016 | Cars & Trucks

1 Answer

How do i bleed the master cylinder on an 02 lancer


Check the slave cylinder on the transmission for leaks, and replace if it is. Bleeding:
1. put fluid in the master reservoir.
2. move the slave actuator shaft so the clutch release lever has not slack.
3. Have someone press the clutch pedal, and crack the slave bleed nipple to let out the air.

Once the slave moves the release lever, you'll be able to decide if the clutch is OK or not.

Oct 09, 2012 | 2002 Mitsubishi Lancer

2 Answers

My clutch seems to have gone out tonight. The clutch is very easy to push to the floor...and it pops back....there's no pressure at all. The clutch fluid is leaking from the hose. Could this be the...


it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

Aug 31, 2011 | Saturn Vue Cars & Trucks

1 Answer

How to bleed 1991 hiace clutch?had new master cyl


need to bleed the slave cyl, on bell houseing.

Jan 11, 2011 | 1991 Toyota Land Cruiser

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

2 Answers

I have changed the clutch master cylinder and the slave cylinder, but still don't have pedal, we have bleed the lines and checked for leaks, no leaks were found. The new slave cylinder doesn't seem to be...


Thn the problem is the clutch master cylinder, it should build up pressure, ok try out this, remove the pipe which is going to the slave cylinder either from the clutch master cylinder or at the clutch slave cylinder and get someone to pump the pedal while you block the pipe and see if there is fluid thrown out with pressure.If there is pressure there thn fit back the pipe and refill the reserviour wth brake fluid and open the bleeding nipple at the slave cylinder let some fluid pour out and tighten it and thn pump the pedal and retry bleeding.
If there is no pressure at the pipe thn its the clutch master cylinder.
Hope this helps!

Dec 14, 2009 | 1997 Acura CL

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

1 Answer

The clutch on my car stuck to the floor. I check the reservoir was completely empty. I have a feeling the slave cylinder is filled with air. I'll need to get the schematics to see how to bleed the clutch.


Bleeding the clutch is similar to bleeding brakes. You'd pump the clutch pedal several times to get the pressure up, and then open the bleeder on the slave cylinder (mounted down on the transmission). Repeat and add fluid as needed until no air comes out.

Two things - first off, some cars have more than one bleed point (the Nissan 300ZX is one of those), so be sure there is only the slave cylinder to bleed. Second, if it went right to the floor, something failed - either the slave cylinder or the master cylinder. Changing the slave is relatively easy - usually two bolts and it comes off, you put on a new one, and bleed it as described above. Often the slave cylinder is less than $30, so it's worth it to try changing it if you can't get the pedal to come back off the floor on its own. A clutch master is significantly more expensive and more difficult to change, so start cheap and easy and replace the slave cylinder if you can't pump the pedal to get pressure built up for a bleed.

Jul 23, 2008 | Chevrolet Cavalier Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...