Question about 1992 Toyota Paseo

Open Question

Remove door panel 1992 toyota paseo

I need to install speakers inside the door of my 1992 toyota paseo how do remove the panel

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: INSTALL SIDE VIEW MIRROR ON A 1997 TOYOTA CAMRY

Yes, you have to remove the door panel.

Remove the 2 plastic protectors on the front edge, and remove the 2 brass colored screws. Next, remove the push pins from the latch side. Push in, and pull out the whole thing. Next, under the armrest, remove the screw. Lift up the power windoe control, being careful to not break the plastic retainer tab. Remove the screw under the window control. Starting at the bottom, pull out the panel, and, when all of the clips are loose, pull the panel straight up. It is best to do this with the door panel as warm as possible, like in a heated garage. Doing this outside in the cold will break all of the plastic retainer clips; they are quite brittle whn cold.

I hope this helps

Thanks for choosing FIxYa for assistance. A FIxYa rating (4 blue diamonds) would be greatly appreciated.

Posted on Feb 23, 2009

Ad
  • 2 Answers

SOURCE: To remove the interior door panel of a 1996 Toyota camry so that

My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
Timmy P.

Posted on Mar 04, 2009

  • 125 Answers

SOURCE: need to remove inside handle to take off inside door panel

remove the screw and move assemble froward by hitting with your hand gently.

Posted on Apr 30, 2009

  • 420 Answers

SOURCE: removing inside door panel to change the speakers

Door panels are easy, first remove all of the screws, some will be hidden under plugs on the door handle. Using a door panel tool (about $5.00 at a parts store) work it around the panel and pop the plastic keepers out. Done.

Posted on May 28, 2009

techbuster
  • 5081 Answers

SOURCE: How do I change the shift gear bulb in a 1992

1.- Remove the rear part of the console. There are 2 bolts inside of the box compartment, they are under a felt.2. Remove the black plastic trim around the shift. It is clamped. You can use your fingers tips by inserting them around the inside cut out of the trim, rear side, lift the trim.
3. Remove a screw that holds the front part of the console at the drivers side. It is located under the steering wheel.
4. Then strecht out side way this front console as much as you can in oder to have space and reach the bulb. You may also have to remove some of the carpet. See picture
You can not see the bulb, so you have to use your fingers to fill it by following the wires up to the bulb socket.
5. Once you have touch the socket, hold it with you fingers and make a 1/4 turn to loose it and then bring it out to remove the bulb.

Posted on Aug 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to check the fuel supply to a 1992 toyota paseo


You need to specify Only one item. "Fuel supply is a large name"
include fuel rail, fuel pump, fuel hose, fuse and relay.

Mai Lor

Feb 28, 2013 | 1992 Toyota Paseo

1 Answer

On my 1992 toyota paseo it has a very high idle of 2800 rpms and i cant seem to find out why


Check water temperature sensor,water thermostat, Speed control throttle servo,chain,or cable binding throttle cable binding!

Sep 09, 2010 | 1992 Toyota Paseo

1 Answer

How do you remove the inside door panel backseat right side of a mercury grand marque 1996


Door Panels REMOVAL & INSTALLATION 1989–91 Vehicles
  1. Disconnect the negative battery cable.
  2. On 1990–91 vehicles, remove the speaker grille.
  3. Remove the retaining screws from the door inside handle cup.
  4. If equipped with armrest courtesy lamps, remove the lens, detach the bulb and wiring assembly from the pull cup and remove the pull cup.
  5. Working through the pull cup opening, disconnect the remote lock rod from the lock knob.
  6. Remove the retaining screw and the remote mirror bezel nut from the power window regulator housing switch plate, if equipped.
  7. Raise the plate to expose the window switch and power door lock switch and disconnect the switches.
  8. Remove the retaining screws from the armrest finish panel.
  9. Remove the retaining screws from the armrest and remove the armrest.
  10. Using a suitable trim pad removal tool, carefully pry the trim panel plastic push pin retainers from the door inner panel. NOTE: Do not use the trim panel to pry the clips from the door inner panel. Replace any bent, damaged or missing push pins.
  11. Disconnect the radio speaker wiring, if equipped.
  12. Remove the trim panel and watershield. To install:
  13. If the door panel is to be replaced, transfer the plastic push pins to the new panel. Make sure that the watershield is positioned correctly to the door sheet metal. Remove the door pull handle from the old panel and transfer to the new one.
  14. Position the door panel loosely to the door belt opening and route the wiring harness through the appropriate access holes in the panel.
  15. Connect the radio speaker, if equipped.
  16. Align the plastic push pins on the door panel to the holes in the door sheet metal and press the pins into place.
  17. Install the armrest and route the window regulator, remote mirror cable and power lock harness through the access hole.
  18. Install the armrest finish panel.
  19. Install the power window regulator switch plate housing to the armrest connecting the power window switch, power door lock switch and remote mirror bezel nut, if equipped, prior to securing the retainer screw.
  20. Connect the lock remote rod to the lock knob retainer boss. NOTE: Make sure that the remote rod is fully seated into the retainer boss, then function manually or with the power switch to ensure smooth operation of the lock knob.
  21. Install the bulb and wiring assembly.
  22. Install the lamp lens, if equipped, and the pull cup.
  23. On 1990–91 vehicles, install the speaker grille.
  24. Connect the negative battery cable. Fig. 1: Front door panel — 1990–91 vehicles 84170064.gif
    Fig. 2: Rear door panel — 1989–91 vehicles 84170065.gif
1992–98 Vehicles
  1. Disconnect the negative battery cable.
  2. If removing the driver's door panel, remove the nut from the outside rearview mirror control switch.
  3. Remove the window regulator switch housing by gently prying up, starting at the front. Fig. 3: Front door panel — 1992–98 vehicles 84170066.gif
    Fig. 4: Rear door panel — 1992–98 vehicles 84170067.gif
    Fig. 5: Remove the window regulator switch housing by gently prying up, starting at the front 89600p08.jpg

  4. Detach all connectors from the switch housing.
  5. Remove the door inside handle cup.
  6. Remove the push pin from the door trim panel upper front extension and remove the screw.
  7. Remove the lower self-tapping screw retaining the door trim panel to the door inner panel. Fig. 6: Detach the switch housing electrical connector and remove the housing 89600p09.jpg
    Fig. 7: Remove the door inside handle cup 89600p01.jpg
    Fig. 8: Remove the screws from the door panel in the front and on the upper extension 89600p02.jpg

  8. On Grand Marquis, pry up the screw covers from the door pull handle and remove the screws and handle.
  9. Lift the door panel upward and snap out the panel. Fig. 9: There are also retaining screws located in the map pocket as well as . . . 89600p03.jpg
    Fig. 10: . . . along the bottom edge of the door panel 89600p04.jpg

  10. Disconnect the necessary wire harnesses and remove the panel. To install:
  11. Connect the wire harnesses to the door panel, as necessary.
  12. Install the door panel by pushing in and down until it snaps into place.
  13. Install all self-tapping screws retaining the door trim panel to the door inner panel.
  14. On Grand Marquis, install the door pull handle, tighten the screws and install the screw covers.
  15. Install the push pin covering screw on the panel upper front extension.
  16. Install the inside door handle cup.
  17. Install the window regulator switch housing and install the nut on the outside rearview mirror control switch, if removed.
  18. Connect the negative battery cable. Fig. 11: Lift the door panel upward and snap out the panel to remove it from the door 89600p05.jpg
    Fig. 12: Rotate the door marker lamp bulb and remove it from the door panel 89600p06.jpg
    Fig. 13: Detach the connectors for the trunklid and fuel door release switches 89600p11.jpg
    Fig. 14: Slide the relay connector off of the door panel and remove the door panel from the vehicle 89600p17.jpg
prev.gif next.gif

Aug 26, 2010 | Mercury Grand Marquis Cars & Trucks

1 Answer

What transmission fluid do i use in my 1992 toyota paseo


Hello, and welcome to FixYa.

According to the Toyota service manual, your 1992 Paseo requires Dexron II automatic transmission fluid.

Feb 09, 2010 | 1992 Toyota Paseo

1 Answer

What tool do i need to change out a starter on a 1992 toyota paseo i cant get the heat shield off


most likely 10mm socket. the bolt on the starter is 12mm and 14mm. there is a 6mm wire nut you have to take it off.
better off go get a set of mm sockets. instead of getting single socket at a time.

May 01, 2009 | 1992 Toyota Paseo

1 Answer

1992 Paseo issues with ideling


GOOD EVENING, IDLE CONTROL VALVE WILL SOLVE HER PROBLEM. ITS ELECTRONIC AND PRETTY EXPENSIVE. LOOK FOR A USED ON AT A JUNK YARD.

Dec 07, 2008 | 1992 Toyota Paseo

1 Answer

Starter on 92 Toyota Paseo


If the battery is good then it could be power cable to starter problem or connection came loose too.

Sep 14, 2008 | 1992 Toyota Paseo

Not finding what you are looking for?
1992 Toyota Paseo Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...