Question about 2000 Dodge Ram 1500 Truck

Open Question

What size are the bed bolts on a 2000 dodge ram

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: brake job/2000 dodge dakota

Last one I did took a 7mm.

Posted on Nov 22, 2008

  • 79186 Answers

SOURCE: 1997 Dodge Ram 1500 transmission will a 1996 interchange

No, the frame is different.

Posted on Nov 30, 2008

  • 1 Answer

SOURCE: 2000 dodge ram 1500 on a 4:10 differential witch transsmition use

I got the info on page from a dodge ram parts seller but I forgot the enet address sorry, any ways thanks a lot.

Posted on Dec 08, 2008

  • 6982 Answers

SOURCE: bolts for upper control arm assy on 1987 DODGE RAM PICK UP

Don't remember the size but they are likely grade 8 bolts not general hardware store stuff. See if you can get them from a junkyard (they usually discard them or cut off with a torch when removing control arm.

Posted on Mar 23, 2009

  • 109 Answers

SOURCE: Ram differential cover replacement

Here is a website that specializes in diff. covers. I'd say look them up and give them a call and I'm sure they can get you fixed up.

Posted on May 06, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace a fuel sending unit in a 1999 Dodge ram 1500

Just as you said ,remove the 8 bolts and get a couple buddys and lift the bed and slide back onto the bumper. This will give you the room needed to do the job.4 bolts up front( 2 on each side) and 4 in the back. Much easier if you had a chain hoist but lifting works too. I don't know if it will lift up enough to do the job with enough room. It was real simple to get the bolts back in place so no worries. Hope this reply isn't to late.

Oct 04, 2015 | Dodge Cars & Trucks

1 Answer

2000 Dodge RAM 1500 will crank but not start.

I used to have the same problem, not so much in the winter though. It was all the time, in any weather. I changed the crankshaft position sensor. Its located at the back of the engine on the passenger side. Its actually in the top of the transmission bell housing. There are two bolts that hold them in. There are allen key bolts, I believe the size is 3/8. My crankshaft position sensor was dirty. It had a lot of rust on it. Its really hard to get to it. there is a ground strap bolt kinda in the way as well above one of the bolts. You will need to get a new rubber grommet from Dodge for your new sensor. has the sensor for $54.95
1_25_2013_1_11_50_am.jpgThis image is from

Dec 16, 2012 | 2000 Dodge Ram 1500 Truck

1 Answer

Where are the 6 bolts to remove the bed of a

crawl under the truck , 2 is at the frt of the bed ,then look inside of the chasis rails at the back 2 near the bumper and 2 between those bolts and the rear end located inside the rails also . there is a small wire on the right frt to remove as well as the 3 screws in the fuel door area you must remove to lift the bed

Nov 26, 2012 | 2004 Dodge Ram 1500

1 Answer

How to replace a fuel pump for a 2000 dodge ram 1500 pickup 5.9 engine - 26 gallon tank

You have two choices.
1. Relieve fuel pressure.
2. Disconnect battery.
3. Lift truck, disconnect fuel lines, filler pipe and pump wires and remove fuel tank,

or lift pickup bed to access top of tank.

Aug 22, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

How do i remove the bed off an 89 dodge ram 50

That is harder yet unless you have an overhead crane. Remove the six stove bolts and all electrical retaianing clips if any mounted to the beds rails and remove

May 03, 2010 | 1989 Dodge Ram 50

1 Answer

How to replace the Fuel pump on a 2000 Dodge Ram

Iusually pull the bed up if the tank in full.remove the bed bolts spare tire lift bracket where it goes through the bed taillight wiring unplug connector remove screws on the filler pipe and the ground stra.get buddy lift the bed up and move the bed three steps to the rear of the truck.front of bed is now over the rear tire lower bed on tire and you are now over the fuel tank with full access to pump assembly without any problems.

Jan 01, 2010 | 2000 Dodge Ram 1500 Truck

2 Answers

Need 2001 dodge 1500 fuel pump replacement diagram

make sure you get the right pump, you need to know your tank size. then take off your bed. you have i believe 6 bed bolts, disconnect tail lights (unplug from underneath) remove bed grounding strap 1 screw, remove bed with help. Disconnect wires, unscrew fuel pump, replace pump. Reverse order to replace bed. jim

Jun 11, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Bolts for upper control arm assy on 1987 DODGE RAM PICK UP

Don't remember the size but they are likely grade 8 bolts not general hardware store stuff. See if you can get them from a junkyard (they usually discard them or cut off with a torch when removing control arm.

Mar 23, 2009 | 1987 Dodge Pickup 2WD

2 Answers

Need to replace fuel pump for my 1998 dodge ram 4x4.

there is an easier way to replace the fuel pump than dropping the tank. I replaced mine last week in about 30 min. I simply took the bed off only six or eight bolts depending on bed size, a few tail light wires and filler neck and over flow. might need someone to help get the bed off though.

Mar 13, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

516 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides