Question about Mazda B2200

Open Question

What steps are there to change a rear axle seal on a 1990 b2200

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

  • 52 Answers

SOURCE: Rear Axle Seal Replacement

remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.

Posted on Apr 22, 2009

  • 335 Answers

SOURCE: REAR AXLE SEAL LEAKING ONTO BRAKE SHOES NEED INSTRUCTIONS ON HOW TO FIX

Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Posted on Apr 28, 2009

  • 71 Answers

SOURCE: How do you change rear axle seal in a chevy pickup

To change the rear seal, yo will need to raise and support the rear of the vehicle. Remove the wheels and drums or rotors (depending on drum or disc brakes.) Remove the rear differential cover bolts and the cover (have a drain pan under the differential) You will likely need to turn the driveshaft so the center pin bolt is acessible at the back or the differential. This is a 5/16" (or 8mm) bolt that is on the right (passenger) side of the differential carrier assembly. I recommend a new bolt be installed here on reassembly. Once the retaining bolt is out, slide the center pin out enough to allow the axle shafts to be pushed in toward the center of the diff. to remove the "C" clips that retain the axle shafts in the carrier assembly. Be careful if you happen to pull the center pin all the way out not to allow the carrier assembly (has the ring gear mounted on it) to turn, as this can rotate the spider gears out of alignment causing a headache on reassembly. With the "C" clip removed the axle shaft can be pulled out of the diff. Inspect the bearing area of the shaft for rust, pitting, or scoring. Remove the old seal and carefully install the new one. Reverse proceedures to install. Take care to note the "C" clips and center pin bolt are properly reinstalled. Fill with 2.5 to 3 quarts of rear axle grease for you vehicle.
good luck.

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove a 1990 rear axle on a Chevy pickup four wheel drive


Diane, links below show how to remove axles on Chevy trucks.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
remove rear axel on 1993 chevy g20
How To Change Your Rear Axel Seal Chevy Silverado
How To install Replace rear Axle 2000 06 Chevy Suburban Silverado GMC...


May 05, 2016 | Cars & Trucks

1 Answer

How to change rear wheel seal


axle seals are covered in the FSM and at alldata.com
so check there,
are you asking for all 25+ steps, the photos, or just the 1 step
for seal.

Jun 23, 2014 | 2001 Dodge Ram 2500 Truck

1 Answer

How do you remove an axle on the right rear of a 1999 explorer? it has a leaking wheel seal.


1. Drain diff if it has a plug.
2. Remove rear cover
3. Undo cross pin bolt and slide the cross pin out of the carrier
4. Push axle shaft in so you can remove the C clip
axle retainers
5. Slide axle out of housing.
6. Remove axle seal and then replace axle seal
7. Reverse steps

May 25, 2010 | 1999 Ford Explorer

1 Answer

Rear axle seal replacement 1994 ford bronco


It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Dec 29, 2008 | 1994 Ford Bronco

2 Answers

Rear Axle Leak


if it is the seal, you will have to remove the caliper and rotor, remove the differential cover and remove the bolt and pin inside the diff carrier housing. push in the axle and remove the axle clip and pull out the axle use a seal puller or prybar to remove seal reverse the steps to assemble

Dec 10, 2008 | 2001 Lincoln Town Car

1 Answer

How to Change Rear Axle Seal?


When you take the rear drum off, look where the axle goes in and if there are 4 bolts around it, you don't have to go into the diff. If there are no bolts holding the axle in, then get a repair manual to guide you through the steps. The seal on an axle that is bolted in place will have a collar that needs to be pressed off and a new one back on. These seals can be bought at a local partsd house.

Nov 09, 2008 | 1989 Jeep Wrangler

1 Answer

Rear end seal leak


You must be refering to the side seals. common problem. the actual problem with those rear ends is the air breather, which cloggs up and that's when your seals blow out, because the pressure in the rear end has nowhere to go and so your seals get blown out. I just did a set on Monday. Anywho, you will need some specialty tools for this. You will need to remove both rear brake assemblys (rotors, calipers). Than look on the other side of the backing plate, there you will see 4 big nuts that hold the backing plate on the axle tube (rear end). Remove those 4 nuts and that's where specialty tools become usefull. You will need a slide hammer. You need to attach the slide hammer onto the axle right by the studs. Use factory whel nuts to attach. Remove axle out of the housing with few good slides of the slide hammer. Once the axle is out, you need to remove the snapp ring, then cut the colar off and remove colar, then remove the old bearing and thats where the seal is. Big help doing this job is a pneumatic air hammer, which helps you remove the stuff off the axle shaft and the slide hammer to remove the axles out. You will need 2 seals, 2 bearings and 2 collars. You may also need the plates with the studs, which had the big nuts, that you removed in first steps of this repair. Kind of a job for someone that has been working on cars and has the tools to do it. Good luck. Oh ya, change the breather and the fluid in the rear end.

Oct 21, 2008 | 2004 Nissan Titan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...