Question about 2008 Chevrolet Impala

Open Question

Where is crankshaft sensor locate on 2008 impala Lt 3.5L engine

Engin will start but won't start after cut off engine, had to wait for about 30 minutes to hour to start

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cadman000
  • 607 Answers

SOURCE: Tires wearing inside on 2008 Impala LT

You most likely have an alignment problem. If BOTH FRONT TIRES are worn the same ( inside edge worn ), that would indicate a TOE- OUT problem such as ( \ / ) . Picture those 2 lines as your front tires going down the road . Hope this helps.

Posted on Jun 05, 2009

  • 312 Answers

SOURCE: I am looking for a fuse panel diagram for a 2008

look behind the passenger side kick panel.

Posted on Dec 27, 2009

  • 312 Answers

SOURCE: po411 code on a 2008 chevy impala lt can anyone

there is no po441 code on this vehicle there is a p0442.

Posted on Jan 11, 2010

  • 11147 Answers

SOURCE: I have a 2008 chevy impala. The car suddenly

ur vehicle is in limp mode[ a safe mode ] which will get u home trying not to cause any damage to engine --theirs a few reasons the vehicle will do this-low oil pressure-transmission problem-have vehicle scanned most auto stores such as auto zone / advanced auto [check ur local area]do this service for free the code gives u a start point towards resolving ur problem

Posted on May 11, 2010

  • 1 Answer

SOURCE: changing a thermostat on 2008 Chevy Impala 3.9L

There are two hoses that come from the radiator. The very bottom hose is conneted to the thermostat housing. Looking at the car from the front under the hood just below the first hose is another one same in diameter and there it is two bolts and you done.

Posted on Dec 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the ambient temperature sensor located ?


images for 2008 Chevrolet HHR LT Where is the .

Outside Temperature Sensor - Chevy HHR Network

www.chevyhhr.net/forums/...hhr-4/outside-temperature-sensor-30594/
Jul 9, 2010 - I had the outside temp sensor go on my 99 Buick. I don't know where it islocated on the HHR, but it was just a plug in sensor. Take out the old, stick in the new.... 2008 HHR LS 2.2 L Auto Built: 12-19-2007. Bought: 4-26-2009 Location of the ambient engine temperature sensor.... Help ...
Mar 26, 2013
Engine Temperature Sensor
Oct 6, 2011
Outside Temp Display
Dec 19, 2008
Outside air temperature problem
Oct 30, 2007
More results from www.chevyhhr.net

Jan 25, 2016 | 2008 Chevrolet Chevrolet HHR LT

1 Answer

My Chrysler 300m won't start with the cam sensor


Bad sensor. Also check crankshaft sensor.

Mar 27, 2013 | Cars & Trucks

1 Answer

2008 Altima won't start or turn over till after 5 or more tries


may need to replace both the camshaft sensor, & crankshaft sensors, I believe that both are located near distributor/ & timing belt cover & top of engine.

Jan 30, 2013 | Nissan Altima Cars & Trucks

1 Answer

My car won't start


I am not sure about restart the engine,but I would check the crankshaft sensor or the crankshaft pulley...

When a crankshaft sensor has failed or is failing, certain timing problems will arise in engine function. The engine may start normally in some cases, but will cut off after a few minutes (or seconds) of operation. More than likely the engine will be unable to start at all. Since the crankshaft sensor is responsible for engine timing, the driver may experience engine backfire or irregular rpm function, if the vehicleicon1.png starts at all.

Dec 21, 2012 | Hyundai Motor 1999 Elantra

2 Answers

MY IMPALA 2007 LT IS LEAKING OIL GASKET WAS REPLACED TWO MONTHS BACK IT HAD BEEN FINE BUT JUST YESTERDAY OIL PRESSURE LOW SENSOR CAME ON & NOW I NOTICE IT'S HAVING A SLOW WATER DRIP PROBLEM AS


Yes or a small bypass hose. You may be able to get a loan of a tester at autozone, oreilys, or advance autoparts. You want a radiator pressure tester. Do not exceed the cap rated pressure. When the engine is warm, you can add pressure and look for water seepage.

There are also chemicals to add to detect leaks if the first method is unsuccessful.

Mar 29, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Crank posion sensor


On all U.S. And Canadian Models Of Pontiac GrandPrix, Chevrolet Impala and Monte Carlo 2006-2008, for 3.5L, 3.9L and 5.3L engines, the camshaft and crankshaft position sensors utilize the same connectors...


11_15_2011_7_56_55_pm.jpg

Image Link: repair_guide/0996b43f80202f50.gif

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 15, 2011 | 2006 Pontiac Grand Am

1 Answer

Where is the idle sensor in the 2000 chevy impala


There is no idle sensor on the 2000 Chevrolet Impala, according to my online resource.

But, there is the following that senses rpm of the engine and thus the idle speed when the Throttle Position Sensor is at 5% or the accelerator pedal is not depressed:

Crankshaft Position Sensor Operation Engine speed is a very important input to the Powertrain Control Module (PCM). Crankshaft speed and position are the basis for many calculations made by the computer. Crankshaft position values are transmitted to the computer by pickup coils also known as Permanent Magnet (P/M) generators, Hall Effect sensors or optical sensors. The Crankshaft Position Sensor (CKP) also known as engine speed sensor is typically located in proximity to the crankshaft.
In addition, the PCM uses the CKP sensor in conjunction with the camshaft position sensor to calculate and perform misfire diagnostics.
Related Symptoms
  • A No Start / Intermittent Start condition - Can be caused by a faulty crankshaft position sensor due to loose connections, bad grounds, high resistance in the circuit, or opens in the circuit.
  • Engine Misfire Diagnostic Trouble Codes
NOTE: Engine Mechanical conditions can also create the same or similar symptoms. (Don't overlook basic mechanical integrity).
prev.gif next.gif

Nov 06, 2010 | 2000 Chevrolet Impala

2 Answers

Were is the crank sensor located at on 2006 impala


Usually ,& depending on engine, is located on the rear side of the engine block behindthe crankshaft balancer. Good luck!

Nov 26, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
2008 Chevrolet Impala Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...