Question about 2004 Mitsubishi Endeavor

Open Question

How to change 2004 endeavor valve cover gaskets

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: bad valve cover gasket, misfire and tapping lifter.

what do you mean with 'bad valve cover' ?I asume it is leaking oil.it means that the rubber seal is not sealing anymore,it has gone hard.tighten the cover bolts sometimes seals it for a while.to get to the rubber seals the inlet manifold has to be unbolted and moved,a fairly involved procedure but easy to do if you have a manual and standard handtools.The misfiring is likely stray arching of the coils .remove the top plastic cover of the motor andlook when it is very dark [like lightsof in your garage] and look for sparking.If so ,replace sparkplugs or/and leads.[remove inlet manifold also]Tapping lifter,works with oil,try engine oil flush and/or change oil brande.if problem persist replace lifter,lifter undervalve cover

Posted on Jun 08, 2009

outdoorsman5
  • 631 Answers

SOURCE: To Change 2004 Mitsubishi Endeavor Transmission filter

Yes you will need a gasket and if you go to the parts store they will sell you what you need. Just tell them what you have and they will give you the filter and gasket. I am not real sure on this year if there is a bolt holding the filter in place and I have looked in all my books on this one but can't seem to find out. If there is a bolt there will only be one more then likely but i really dont think you have a bolt. Just take the pan down and see if you can gently pull down the filter. Most of the time they are just up there with a O-Ring to hold them in.

Posted on Aug 05, 2009

  • 69 Answers

SOURCE: I changed the oil, spark plugs and valve cover

test to make shore you ignition coil is working" unplug any plug wire and then try starting it...you should her the ticking from the ark of electrisity from the coil to the engine block its self... first: be shore youve connected the spark plug wires in to the right slots on the ignition coil second: make shore the wiring harness just upstream from the air filter is connected"without it my montero want start" third:make shore all harmesses are connected and tight.... forth: now turn the car on..but dont start it.. and see if the check engine light goes off.... fifth:try giving it a lil bet of gas when trying to start..... thats all i can think of, srry for spelling...hope it helps

Posted on Jul 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause the oil to build up on valve cover gasket center bolt 2004 PT Cruiser 4.0l engine?


I'm pretty sure Chrysler never put a 4.0L engine in a PT Cruiser (V6? V8?). And since the valve cover gasket is located between the valve cover and the cylinder head, there is no bolt that holds just the valve cover gasket in place - all the bolts hold the valve cover in place. If there is excess oil around one of those bolts, you have a break in the gasket (or a bad gasket if the gasket is for the bolt only) or the bolts are not tightened to specification.

Nov 09, 2016 | 2004 Chrysler PT Cruiser

1 Answer

Location of pcv valve for 2004 mitsubishi endevor


As you are looking at the Engine bay, on the top of the forward valve cover, left hand side. You will see it screwed in to the valve cover with a hose connected to it, about an 1.5 inchs long.

Jun 05, 2014 | 2004 Mitsubishi Endeavor

1 Answer

2003 Ford F-150 4x4 5.4L with a valve rattle or pinging noise.


-Possibly valve has too much clearance
-If sound from the valve. Open cover and adjust to specification.


Good Luck
Mai

Nov 12, 2013 | 2004 Mitsubishi Endeavor

1 Answer

We change the spark plug of my aveo 2004, and we found out that there is a oil leak on the third cylinder, what may cause the problem?


The valve cover has rubber o-ring seals that fit into the valve cover and seal oil out of the spark plug wells. Over time, they get hard and shrink, allowing oil to enter the plug wells from the top of the engine. You need to remove the valve cover and replace the valve cover gasket and o-ring seals. The seals should come with the valve cover gasket set.

Hope this helps,
Dave

Jul 03, 2010 | 2004 Chevrolet Aveo

1 Answer

We need to know how to change a valve cover gasket on a 2004 suzuki verona 2.5L ENGINE


There are probably 8 - 12 bolts/nuts that attach the valve cover to the cylinder head. Remove the bolts, clean the mating surface, install new gasket, and reattach the valve cover with the bolts.
You may need to remove the following spark plug wires vacuum lines air cleaner assembly oil filler cap

Jan 06, 2010 | 2004 Suzuki Verona

1 Answer

To Change 2004 Mitsubishi Endeavor Transmission filter


Yes you will need a gasket and if you go to the parts store they will sell you what you need. Just tell them what you have and they will give you the filter and gasket. I am not real sure on this year if there is a bolt holding the filter in place and I have looked in all my books on this one but can't seem to find out. If there is a bolt there will only be one more then likely but i really dont think you have a bolt. Just take the pan down and see if you can gently pull down the filter. Most of the time they are just up there with a O-Ring to hold them in.

Aug 02, 2009 | 2004 Mitsubishi Endeavor

2 Answers

Changing valve cover gasket on 2001 dodge stratus, how


remove all the components in the way of the valve cover.  Then remove the valve cover and replace the gasket and reassemble.
usually about a 3 to 4 hour job.

Mar 16, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...