Question about 1999 Lexus Gs 300

Open Question

Crankshaft position sensor location 99 rx300

Location

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 99 RX300 Engine code keeps coming up lean

I just had the same thing happen to my 99 RX300. I replaced the MAF sensor and cleaned the throttle body. We cleared the codes and check engine light came on again... with a knock sensor code. Had to replace knock sensors. Found some great info on how to do that here. http://us.lexusownersclub.com/forums/index.php?showtopic=41266&mode=threaded Car drives great now!

Posted on Jun 26, 2009

Ad
  • 53 Answers

SOURCE: How difficult is it to replace the transmission

your vss can be in the rear of the trans, or transfer case or also in the rear diff, is your check engine light on ?

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft placement sensor located?


Do you mean the crankshaft position sensor

May 21, 2016 | Cars & Trucks

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

1 Answer

Where is crankshaft position sensor on a 99 grand am 3.4


Hi, is located on the right side of the harmonic valancer

Nov 16, 2012 | 1999 Pontiac Grand Am GT

2 Answers

99 stratus 2.5 v-6/no spark.will crank over.


CRANKSHAFT POSITION SENSOR - 2.5L

REMOVAL
  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 19, 2012 | 1999 Dodge Stratus

1 Answer

How do I change a crank sensor on a 1998 Buick Lasabre?


1998 Buick Lesabre 3.8L SFI OHV 6cyl

The dual Crankshaft Position (CKP) sensor is mounted to the front of the engine, attached to an aluminum bracket mounted to the left side of the engine at the timing chain cover. A 4-wire connector plugs into the sensor, connecting it to the ignition control module.


1_23_2012_5_18_14_pm.gif

Fig. 1: The Crankshaft Position (CKP) sensor is mounted to the front left side of the timing chain cover

REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield.

1_23_2012_5_19_40_pm.gif

Fig. : If so equipped, remove the crankshaft position sensor shield

  1. Unplug the sensor electrical connector.
  2. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  3. For 1992-99 vehicles, remove the sensor from the block face.

To install:
  1. For 1987-91 vehicles, perform the following:
  2. Loosely install the crankshaft sensor on the pedestal.
  3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
  4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm).
  5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
  6. Remove the special tool.
  7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  1. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.

  2. Install the balancer on the crankshaft.
  3. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 7 degrees rotation.
  4. Install the inner fender shield and the right tire and wheel assembly.
  5. Carefully lower the vehicle.
  6. Install the serpentine belt.
  7. Connect the negative battery cable.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

Need to replace the crankshaft position sensor


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

  8. Unplug the sensor electrical connector.
  9. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  10. For 1992-99 vehicles, remove the sensor from the block face. To install:
    1. For 1987-91 vehicles, perform the following:
    2. Loosely install the crankshaft sensor on the pedestal.
    3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
    4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
      Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

    5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
    6. Remove the special tool.
    7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  11. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76°rotation.
  14. Install the inner fender shield and the right tire and wheel assembly.
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1999 Oldsmobile 88

1 Answer

Where is the crankshaft sensor located on the dodge dakota 99 sport v6


On the V6 and V8 engines, the crankshaft position sensor is bolted to the cylinder block near the rear of the right cylinder head.

2e977ab.jpg

Jul 30, 2010 | 1999 Dodge Dakota

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...