Question about Cars & Trucks

Open Question

Diagram of electrical coil for mazda bj5p

Trying to find sensors for coils

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: coil problem [ misfire DTC code]

rx8 have a history of coil packs going bad internally and grounding out. best way to check if theyre bad is to pull the packs and inspect the back side. if you have discolorationg on the back side your packs are bad or are going to be bad soon. inspect the plugs if they are fouled or burnt replace them along with the coil packs.its a good idea to replace the wires too. and do not use cheap aftermarket parts. this will only cause more problems in the future. use oem or performance parts.

Posted on Dec 05, 2008

Ad

SOURCE: O2 sensor

There should be two O2 sensors. If you look inbetween the engine and radiator following the exhaust manifold down to the exhaust pipe you should run into the 1st O2 sensor, following the pipe down stream under the vehical towards the catalytic converter you should find the second O2 sensor. The 1st O2 should be easy but the 2nd might be difficult depending on your abilities. Coils will depend on 4 or 6 cyls, 1 for each cyl. Repair man, go to, pep boys, napa, auto zone, advanced auto parts to name a few.

Posted on Mar 18, 2009

c17hydro
  • 2984 Answers

SOURCE: MASS AIR FLOW SENSOR REPLACEMENT & DIAGRAMS

Very easy for the Mass Air Flow Sensor....it is in the duct between the throttle body and the air filter box. Just unclamp the tube and remove the old and replace with the new.

13d0cec.jpg

On your pack....I need the engine size.


Posted on Mar 26, 2009

  • 1 Answer

SOURCE: Ignition wiring diagram Mazda B2000 1986

im trying to fix the break lights in my mazda b2200 its a 92 i fryed all the break light wires and dont know where they run to if i could have some one tell me where they run to it would really help

Posted on Jul 15, 2011

  • 1 Answer

SOURCE: mazda 2000 astina flat spot

I have seen the rotor button cause hesitation on take off, on several different Mazda Astina's.
Not a certainty, but a probable cause regardless.

John Donohue

Posted on Nov 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Mazda 6 coil pack replace


Unplug the coil pack spark plug wires and mark where they go for future reference, unplug the coil pack electrical connector and then remove the retaining screws that hold the coil pack to the engine. You never say engine type, V6 or 4Cyl.

Jun 29, 2017 | Mazda Cars & Trucks

1 Answer

Will the oil pressure sensor prevent ignition to the motor? 1999 Ford Laser - KN or Mazda 323


no oil sensor not related

fuel ,spark a broken timing belt

fuel
pump or relay you should be able to hear the fuel pump working
if engine light is on
crank angle sensor

Nov 05, 2016 | Ford Cars & Trucks

1 Answer

I have a 02 mazda millenia and the car will turn over but will not start i replaced the camshaft sensor and i still have no power to my coils anyone have any idea what it could be HELP


I'm showing one coil and a distributor on a 2002 model.
The wiring diagram shows the coil is powered by the key switch thru a 10amp fuse marked engine.

Feb 10, 2014 | Cars & Trucks

1 Answer

Need diagram for ignition coils for 2001 Mazda Tribute. Tripping code: P0351 Ignition Coil Primary/Secondary Malfunction???? Thanks


Same as Ford Escape.
P0351 - Ignition Coil A - Primary/Secondary Circuit

Cylinder #1, Pin 26 at the PCM, computer.

I would replace the coil on the plug (COP) for that cylinder and see if its' ok. If not, then it is possible that the bad coil took out the driver in the PCM. The test at Pin 26 to see if the light blinks, must be done with the correct tester or it will damage the PCM.

Hope it's the coil.

report results.

4 cylinder or 6 cylinder engine?

Jul 14, 2011 | Mazda Tribute Cars & Trucks

1 Answer

I have a mazda626 2.0 and the coil wiring isv of,i need a diagram for the coil


have you tried auto parts store they have wireing diagrams in the back of books you can buy under 20 dollars

Feb 24, 2011 | 1988 Mazda 626 Turbo

1 Answer

Replacing sparkplugs and wires on 2000 Mazda Protege 1.6 lt engine On top of cylinder 2 and ? are electrical components that attach to plugs. What are they? trying to find diagram and assistance for...


They are the ignition coils, the spark plugs are under them. When you have them off before pulling the spark plugs make sure the holes the plugs are in do not have oil in them, if so you will need new coil boots, plugwires and a valve cover gasket as well.

Mar 19, 2010 | 2000 Mazda Protege

2 Answers

Ignition wiring diagram Mazda B2000 1986


my 88 mazda b2200. none of the lights or fuel pump come on when i turn the key over, but i know the wires aint hooked up. im just trying to figure out where they are located

Mar 25, 2009 | 1988 Mazda B2200

1 Answer

Will not start


check the coil pack and the crank sensor and the timing cause you could have a bad timing belt also go to your local library and there you can get pictures and diagrams showing you detailed instructions

Mar 08, 2009 | 2000 Mazda MPV

2 Answers

Coil problem [ misfire DTC code]


rx8 have a history of coil packs going bad internally and grounding out. best way to check if theyre bad is to pull the packs and inspect the back side. if you have discolorationg on the back side your packs are bad or are going to be bad soon. inspect the plugs if they are fouled or burnt replace them along with the coil packs.its a good idea to replace the wires too. and do not use cheap aftermarket parts. this will only cause more problems in the future. use oem or performance parts.

Oct 10, 2008 | 2004 Mazda RX-8

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...