Question about Cars & Trucks

Open Question

How do I replace drivers door handle on Peugeot partner

Drivers outside door handle has broken off.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 958 Answers

SOURCE: Broken rear door handle

hi jim,

you need to open the door panel, after removing the panel, raise up your window completely and you can see the nuts or bolts that are holding your door handle.

tnx 4 using fixya,


drcool

Posted on Oct 05, 2008

Ad
  • 8 Answers

SOURCE: 325 ci conv

ok normally there are only a few screws or bolts that hold the door panel on sometimes they are located on the door handle on the inside somewhere or inside a small pop out panel on the door panel itself. Dont force anything because if you break any of the clips then you are in real trouble and have to either replace the clips or replace the door panel itself. just check and see if on the door handle has any screws or bolts. Most of the time there are just a few screws or bolts and a few clips. If there are clips try to pop them out really easy ok. If you have anymore questions just ask. I hope I helped

Posted on Oct 06, 2008

PJ Vernon
  • 40 Answers

SOURCE: Replace driver's side door hdle & locking mechanism on 02 Protege

Removing the door skins are not hard, the problem is that they normally use a special tool. Without the tool you may break a few of the plastic clips. If so no worries go to your local automotive department and look for the clips. 
You will also have at least one screw that attaches the skin to the door frame. Usually remove the bottom of door panel and work around both sides until you get to the window. Then remove the screw and unplug any of the power options..
Haynes or  Chiltion manual for your car should show you details.. It is easy for the average DIY person.
The handle is just as easy. Do you have metric and torx because you will need them.

Posted on Dec 03, 2008

michigan man
  • 3533 Answers

SOURCE: changing outside door handle drivers door

first disconnect the negative side of battery and then open the door and start looking for small black screws or nuts then remove you find some hidden behind what look like little doors that you will need to remove with a screw driver becareful not to pry the plastic completely out of the door panel itself because if this happens you will have to figure out a way to repair so the panel will stay on the door get a thin pry bar to this job or a butter knife

Posted on Jan 05, 2009

  • 6 Answers

SOURCE: third door handle is broken

its 150.00 dollers at the deler or cheper at auto zone the 3rd door panal comes off and the bolts that holds it in is in there

Posted on Sep 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fix door handle Ford Ranger outside drivers


One can be purchased from rockauto or another store and replaced relatively easily.

Oct 10, 2017 | Ford Cars & Trucks

1 Answer

1998 Isuzu Rodeo Drivers Outside Door Handle doesn't work


The door skin needs to be removed you will need 1/4" drive ratchet, extensions, metric box end wrenches, a long needle nose pliers, screw drivers,a pro pick set and some mechanical ability, verify the linkage is intact, if it is you probably have a broken handle, if the outer handle is broke E-Bay has them new and used or you can go the dealer route. the time to repair is usually 1 to 2 hours. GL

Aug 18, 2012 | 1998 Isuzu Rodeo

1 Answer

Drivers door wont open


If it were me , I'd remove the inside door panel and take it from there. It may be that you can pry open the lock mechanism with a screw driver or a similar tool, allowing you to open the door - which obviously you must do. Even that, though, will not solve the cause of your problem. You may wind up at the dealer.

Aug 19, 2017 | 1986 Ford Tempo

1 Answer

2003 volvo xc90 t 6....drivers door will not open from inside, ok from outside. self locking ok open/shut. It has appearance of child lock active which for a drivers door doesn't exist i assume. the...


the inside door handle is probably broken. the cable may have popped out but usually its because the clips on the inside door handle break off. luckily you can just replace the handle and not have to get a whole new door panel

Jul 11, 2011 | 2004 Volvo XC90

1 Answer

My 2004 Volvo S40 Drivers Side Door will not open from the outisde. The handle is not broken. There is no child safety lock on. It was fine on Friday. Car wasn't used on Saturday or Sunday but then Monday...


the handle might of broke internally, theres a rod and a clip that gets attached to the handle. i would take the door panel off and visual look at the latch mechanism and the rod that goes from that to the outside handle

Jul 11, 2010 | 2004 Volvo XC90

1 Answer

My drivers door wont open the outside.


Broken handle. You can get another from years 89-94. Just be sure to change out the lock cylinder with the one that is broken.

May 19, 2010 | 1990 Jaguar XJ6

1 Answer

Cant find diagnostic port in peugeot partner


Look under dash near drivers door

Feb 25, 2010 | 2006 Peugeot 505

1 Answer

How do I fix a broken outer door handle on he drivers side?


Is there anything connecting the handle to the door latch assembly? Is the lock cylinder in the key hole and secured? It just sounds like the linkage may have slipped off the door handle

Aug 17, 2009 | Mazda Tribute Cars & Trucks

1 Answer

Diagram for replacing exterior door handles


ok. first u remove the door panel(s), with the window rolled up, u will be able to see the back side of the exterior door handle. there will be three bolts, they are size 10metric. there is also a rod attached to the handle held in place by a plastic clip, remove the rod, then remove the three bolts. from the outside remove the exterior door handle being careful not to scratch painted surface. Repeat for the other door(s). Repeat this for installation.

Dec 14, 2008 | 1997 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...