Question about Cars & Trucks
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
it is inside the timing cover in most cases with hyundai the timing belt will have to be removed so the crank gear can come off the sensor is usually behind the gear especially if it is a 6cyl if it is a 4 cyl then the wire goes behind the timing belt make sure the timing marks are lined up so when you reassemble it is lined up
Posted on Aug 29, 2009
Testimonial: "Thank you for the advices Ill get cracking on it"
Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2
some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2
Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.
Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.
Most GM engines have #1 cylinder located on the left bank, (or Driver's Side) of the engine,
So, the answer to your question would be that you are looking for the sensor located before the catalytic converter on the right (or Passenger Side) of the truck.
Posted on Oct 17, 2009
B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter
You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks
Posted on Oct 20, 2009
You need to check two things.
First, there is a heat shield on top of the front of the motor where the o2 sensor you already replaced is. It's got (4) 12mm bolts. Remove it and check the exhaust manifold (big thing you put the o2 sensor into) for cracks. If there are any cracks, you'll get o2 sensor codes. Replace the manifold.
Second, if the manifold is fine start the car and listen to the exhaust pipe under the engine for leaks. Or if you already know the exhaust is loud... that's gonna do it too. A leaking exhaust pipe on an Accent will set secondary o2 sensor codes.
SHOULD you try to change it yourself, you will need a 7/8" wrench, and a new o2 sensor, or flex pipe, or manifold depending on what's broke. Do NOT touch the tip of the new or old o2 sensor to ANYTHING when you take it out or install it or it will be ruined permanently. Run the car until it's at it's normal operating temperature. Raise the vehicle, and take the o2 sensor out of the car (see below to understand which one) using the 7/8" wrench or if you got fancy and bought an 02 sensor tool... use it.
Replace whatever parts are bad (manifold or pipe) or just replace the sensor you need. Then restart the car and take it to a parts store and have them clear the code. The code (and check engine light) won't return right away, it usually takes a few days. If you did everything right you should be good. If not, it's not a terribly expensive job to have done and by now you should be able to explain to them what's wrong based on what you found when you looked at the car. Just tell them everything you checked and what you saw.
Education: I'm not sure where that half baked answer about o2 sensor 1 being near cylinder one came from but here's the real deal.
Sensor 1 is always BEFORE the catalytic converter
Sensor 2 is always AFTER the catalytic converter
Bank 1 and Bank 2 refer to which SIDE of the exhaust on 6 and 8 cylinder engines. Bank 1 is usually left side, Bank 2 is usually right side.
So... O2 sensor B1S1 refers to the O2 sensor BEFORE the converter on the LEFT side of the motor.
Posted on Nov 23, 2009
bank 1 is the drivers side,and it is the down stream sensor,the one after the cat,converter,If this was helpful,please let us know,thank you.
Posted on Jan 03, 2010
Tips for a great answer:
Dec 28, 2015 | Cars & Trucks
Aug 09, 2015 | Hyundai Cars & Trucks
May 21, 2014 | 2006 Hyundai Trajet 2.0
Oct 05, 2013 | 2001 Hyundai Elantra
Oct 03, 2012 | 2001 Hyundai Trajet
Aug 31, 2009 | 2001 Hyundai Accent
Aug 31, 2009 | 2001 Hyundai Sonata
Aug 29, 2009 | 2001 Hyundai Sonata
Jun 12, 2009 | 2001 Hyundai Santa Fe
May 27, 2018 | Ford F-150 Cars & Trucks
May 27, 2018 | Toyota Cars & Trucks
63 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: