Question about 1984 Isuzu Gemini

Open Question

Why is my 1984 holden gemini not starting

Dont know my firing order to my 4 1983 holden isuzu

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 1994 isuzu holden rodeo injection timing adjustment

try u-pull our patrs

Posted on Sep 12, 2008

snownbird33
  • 120 Answers

SOURCE: Holden 94 rodeo petrol

Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Posted on Sep 30, 2008

  • 35 Answers

SOURCE: Firing order for 2001 isuzu trooper

this link was from the autozone online manual i think this is what your looking for thanks jeff http://www.autozone.com/N,26400242/shopping/specsSelect.htm

Posted on Dec 02, 2008

  • 33 Answers

SOURCE: firing order 1995 isuzu rodeo 3.2v6

123456 IS THE FIRING ORDER... RIGHT BANK (RIGHT AS IN SITTING IN THE DRIVERS SEAT NOT STANDING IN FRONT OF THE CAR)STARTING AT FRONT IS CYLINDER 1 THEN 3 THEN 5 THEN THE LEFT BANK IS CYLINDER 2,4,6, FRONT TO REAR... THE COILS FROM LEFT TO RIGHT (STANDING IN FRONT OF CAR) ARE 1,4,6,3,2,5 HOPE THIS HELPS

Posted on Mar 27, 2009

  • 2 Answers

SOURCE: can not find a radiator to fit 84 rodeo

gemini radiator should be ok as they are same engine

Posted on Apr 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Head bolt torque settings and order for 24litre petrol engine Austalia Holden rodeo Isuzu motor c24se Holden Rodeo 2003


this is USA forum
not a single HOLDEN here
not a one.
why ask us,
why not join , real forum that covers your country

http://www.planetisuzoo.com/

Mar 12, 2017 | Isuzu Cars & Trucks

2 Answers

Good Day. How do I set the valves gap for a Isuzu 161Z motor, is it on rocking stage or completely loose??


completely loose -- piston on tdc compression stroke
if you know the firing order of the engine if no 1 piston is on compression stroke , the next piston to fire will be on valve overlap or valve rock
when it is in the valve rocking situation then no 1 piston will be at maximum clearance for adjustment purposes
repeat the process for the next piston to fire
for example "- 6 cylinder
firing order -- 1-5-3-6-2-4
with no 1 on compression , no 5 valves will be rocking, no 5 on compression no 3 valves will be rocking with no 3 on compression no 6 valves will be rocking and so on

Nov 26, 2016 | Isuzu Cars & Trucks

2 Answers

2006 holden rodeo with 3 ltr Isuzu engine. Will run and drive and then stop with error code p1630a. If you pump priming pump and hold throttle down it will start and run for a while.


P1630 "Theft Deterrent Learn Mode Active", this causes a stall and the hard start. You may have a problem with the control module.

Aug 31, 2016 | Isuzu Cars & Trucks

2 Answers

2000 holden vt commodore 3.8 What is the firing order please


Since this is just a Buick 3.8 V6 the firing order is
1-6-5-4-3-2

Apr 26, 2016 | Holden Cars & Trucks

2 Answers

Holden gemini repair


do you have to depress the clutch to start the car?Well it might be something in the( safety switch) of the clutch that is shorting out causing it to want to die out

Dec 31, 2013 | Cars & Trucks

1 Answer

1984 pontiac bonnerville plug firing order photo


Hi,
I don't know your engine size, but the link below is a picture of the GM small block firing order with distributor.
The firing order, which should be cast into the intake manifold, for the chevy small block V8 is 1-8-4-3-6-5-7-2. The firing order is the numerical sequence in which the spark plugs are fired. The insertion position of each spark plug wire around the circumference of the distributor cap can be found according to a clock face. The insertion sequence determines the firing order. The firing order is followed clockwise around the distributor cap starting from the 6:30 position with the 6:30 position being the number one cylinder spark plug wire.

http://www.classiccarauto.com/impala/how_to/images/distributor.png

Hope this helps...

Aug 27, 2009 | 1984 Pontiac Bonneville

1 Answer

Torque specs for big ends, mains, cam caps


found local Adelaide engine reconditioning shop that knows all about g200 twin cam EFI isuzu motors for parts and engine components ( pistons, rings, bearings etc. ) and machining, Chris Milton engine reconditioning. They will do machine work for me so then i can put it together.

May 23, 2009 | 1999 Isuzu VehiCROSS

1 Answer

Gear Oil Refill in Hoden gemini 1986


two plugs fill from the bottom one until it comes out the top one

May 20, 2009 | 1984 Isuzu Pickup

1 Answer

Can not find a radiator to fit 84 rodeo


gemini radiator should be ok as they are same engine

Feb 15, 2009 | 1984 Isuzu Pickup

1 Answer

STARTS AND IDELES FINE WHEN PUT IN GEAR AND PUSH ON GAS IT HESITATES BAD IF I FLOOR IT WILL GO


Holden Gemini has two different carbys the difference is the number of pins on wiring loom plug to carby, a couple of these pins are connected to switches on gearbox and it changes the carby settings depending witch gear it is in .One switch on gearbox is reversing lights and others if fitted are for carby.

Jul 18, 2008 | Isuzu I-Mark Cars & Trucks

Not finding what you are looking for?
1984 Isuzu Gemini Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...