Question about 1989 Pontiac Sunbird

1 Answer

Not sure if t-stat is in properly

Need diaghram

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Always remember pointy part of thermostat goes toward radiator.

Posted on Feb 14, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Niisan v6 patrol need a diaghram of ditributor stripped down?


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Nov 14, 2016 | Nissan Cars & Trucks

1 Answer

Rad hot top to bottom new stat fitted pies into heater matrix one hot other cool rad back flushed and heater mattrix


Be sure that cooling system has been bled properly after . Start engine while cold with cap off, and heater on. Let engine get up to normal operating temperature and allow thermostat to open and close 2 or 3 times and rev engine slightly once in a while for 5 seconds or so to help improve flow. If you have rad where you can actually look in and see flow, that's better otherwise watch coolant return bottle and temperature gauge. Feel if any difference at heater as you bleed air out. Once you start to feel better /good heat, then it should be bled properly, then top up coolant return bottle and re-install cap properly. Let me know if that helps.

Nov 25, 2013 | 1999 Dodge Ram

1 Answer

I need wiring diaghram for 2009 chrysler pt cruiser to put in remote starter


for most of my electrical i go to auto zone web site to get that stuff

Dec 24, 2012 | 2009 Chrysler PT Cruiser

1 Answer

What do i need to remove to take the eveaporter core out of a 99 ford taurse


It's under the dash, may require removing the dash, your best bet is to go to alldata.com

and purchase info on just your make and model car, it cost under 20 dollars, and will show

you step by step with diaghrams what you have to do to replace your evaporater core. plus

you can print out diaghrams so when you have to put it back together, your not left with bolts

and parts. and it's for any thing to do with your car from brakes to engine work.

good luck!

Jul 23, 2011 | Ford Taurus Cars & Trucks

1 Answer

How to change the thermostat on a 97 acura rl


I just changed a t-stat in a 96 last night. The location is in an "abnormal" location from normal domestic cars. The t-stat is at the engine block end of the lower radiator house. Follow it from the radiator up to the engine block. The one on my car the housing and the T-stat is located behind the throttle bottom. If you are not some what mechanically inclined stop reading this right now and head to a mechanic. If you choose to replace it yourself you have to remove the all covers (your intake and throttle cable cover). You will also have to remove any vaccum houses that are atteched to the air intake and throttle body assymbly. You'll have to remove your air intake house and the "sleeve" that is atteched to the air intake hose and the throttle body air intake opening. You'll also have to remove the cables from the flap control (engage them by pulling back the sprung rocker and removing the cable head through the slot that locks it into the rocker lever). Once both cables have been removed you'll have to remove the cable plate from the throttle body. Now you'll have to remove the throttle body itself from the intake. That is done by removing the four bolts securing it. (If you do not have a torque rench, borrow one and get the specs from your local automotive store). There is a gasket that needs to be replaced between the throttle body and the intake. Once that is all out of the way you'll see the T-stat covering, remove it and expose your therostat. When you remove the T-stat pay attention to the position of the T-stat. Put the O ring on the new T-stat and reverse above prossess in order to properly rebuild the throttle assembly. Be sure to regasket the throttle body and torque the four bolts to specs, also make sure you tighten in a cross pattern to prevent any warping or carcking. AGAIN

Jul 06, 2011 | Acura RL Cars & Trucks

1 Answer

2002 Ford Escort timing belt diaghram?


do it yourself books , haynes, chilton , check half price book stores for your make and model . then try auto parts store , they also may be able to pull a diagram up and show you at the store

Jul 28, 2010 | 2002 Ford Escort

1 Answer

I have no heat but my A.C and blower works


I would suggest double checking the heater core connection, make sure every thing is connected properly. check your t-stat make sure its not stuck open. Do so by feeling the upper hose, it should be a warm-hot feel, if its cool or cold replacing the t-stat would fix that problem.

Dec 06, 2009 | 2003 Mitsubishi Galant

1 Answer

2003 Dodge Durango is overheating


are you sure that you put the t stat in the right way??is there anything blocking the rad mud ect ect???did you put more coolant in it after changeing the t stat?...is the water pump working proper?...the head gasket may be leaking..this should help solve your issues

May 07, 2009 | 2003 Dodge Durango

1 Answer

1986 FOR BRONCO II v-6 ENGINE 4 WHEEL DRIVE AUTOMATIC 2.9 LITER


LOCATE EGR VALVE,, BELOW HOUSING, THIER ARE OPENINGS GENTLY, USING FINGER, INSERT IN OPENING, PUSHUP ON DIAGHRAM, WHEN YOU RELEASE FINGER IT SHOULD RESEAT AND SEAL,LISTEN TO ENGINE OPERATERTION FOR VARIATION TO IDLE, YOU HAVE JUST CHECKED TO MAKE SURE DIAGHRAM IS NOT BAD, NEXT CHECK VACMN TO VALVE,AND CONDITION OF HOSE.

Oct 05, 2008 | 1986 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...