Question about 2006 Jeep Commander

1 Answer

My 2006 jeep commander will not start

First it would start but would not stay started tried 3 times now it will not start at all

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

For acurate diagnosis I would need some more info. LIke are u using original key?, Does vehicle have fuel in it? Does the engine turn over when you turn key on?. I Have many questions that if you answer may lead to solution to your problem, Remember the only stupid question is the one you didnt ask. (l.o.L)

Posted on Feb 14, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

  • 439 Answers

SOURCE: the mfg alarm system on my 2006 jeep commander

There's really not very much you can do because of it being a factory alarm you will have to take it to the dealer and have them check it. They may just need to reduce the sensitivity (if too sensitive cars driving by and set it off). If it is bothersome and you have to do something about it, you can disconnect your cars battery until you can drive it in.

Posted on Sep 27, 2009

  • 715 Answers

SOURCE: I have a 2006 jeep commander.When i try to start

no check warranty

Posted on Oct 30, 2009

  • 645 Answers

SOURCE: ac/heater fan switch problem on a 2006 jeep commander

next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Posted on Feb 13, 2010

Testimonial: "This info was very helpful but need a little more info of where the fan motor is located. I will post another question to find that info."

Gozer
  • 435 Answers

SOURCE: install a altenator for a 2006 jeep commander

I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

Posted on May 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2006 jeep commander rolls over but won't start?


You mean the engine cranks over but won't start ? If this is the case you need to check for spark an fuel to see how to proceed . No Start Diagnostic Basics EricTheCarGuy

Feb 25, 2015 | 2006 Jeep Commander

1 Answer

Orange engine looking light on dash panel for 2006 jeep commander


It is probally the check engine light, If it stays on while you are driving,It should be scran before you have serious trouble with it,

Nov 27, 2012 | 2006 Jeep Commander

1 Answer

When i try to start my 2006 Jeep Commander all I hear is a clicking noise.


May be the starter solenoid, or a weak battery. Especially in cold weather, a weak battery will not have enough amps to kick in the solenoid on the starter, but may start after a few tries. Also may be as simple as a loose or corroded battery connection. Get the battery checked first, as this will not get better, only worse with time. If the battery and connections check out, then have the starter solenoid checked.

Jan 12, 2012 | 2006 Jeep Commander

2 Answers

2006 jeep commander makes a clicking noise when I turn ignition, all lights and radio come on but car won't turnover, what is it?


I have had this issue 2 times, both times it was the battery having damaged/dead cells. You can sometimes get it to start by putting your foot on the break, turning the key to the on position, putting the car in neutral then starting it. I purchased my Commander new in 2006 and have had to replace the battery 2 times since, both times this was the initial symptom. I have 120K miles and still love my Commander

Mar 06, 2011 | 2006 Jeep Commander

1 Answer

2006 jeep commander check engine light stays on after jeep sat for 5 days in ice storm and was not started


I don't think I would be concerned about the vehicle sitting for 5 days. Get it scanned and work on a fix,for why the light came on.

Feb 15, 2010 | 2006 Jeep Commander

3 Answers

2006 Jeep Commander Intermittent Starting Problems


Common problem in snow country where salt water can corrode starter parking gate wire connection at started tab. Just cleanthe connector and tab, coat in dielectric grease, problem solved in 15 minutes!

Sep 12, 2009 | 2006 Jeep Commander

1 Answer

Cranks but does not start , wiggled the auto gear shift when it happened before and it started but this time no luck, 2006 jeep commander


you starter is probably gone - you can take a long thin object and try to tap the starter as you crank the car - if this works, must replace the starter

Jul 12, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...