Question about 1995 Ford Ranger Supercab

1 Answer

How do you unhook the clutch hydraulic line from transmission

4.0 liter

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There is a pressure clip at the end of the line once you push both side in it will release but be careful they are easy to break and expensive to replace

Posted on Feb 13, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 gmc Manuel transmission clutch don't work


Is it a hydraulic activator?

Clutch Replacement - Chevrolet K-1500 ' GMC ' Chevy ...

? 15:38
www.youtube.com/watch?v=4y-32SqULUs
Jan 17, 2012 - Uploaded by ClassicManuals.net Clutch Replacement -- Chevrolet Chevy C/K 1500 Clutch Replacement. GMC K1500 5.7 liter Clutch ...

Aug 23, 2015 | GMC Cars & Trucks

1 Answer

Where is the slave cylinder on 91 gmc sierra


I had a 92 Chevy Cavalier which had the hydraulic clutch system like yours. I had intended to flush and purge the hydraulic clutch system at the same time I flushed and purged the brake system. I traced the hydraulic lines from the master cylinder into the front of the transmission where the clutch is located. This is the most likely place to look for the slave. I didn't find a way to bleed the lines with the transmission still in and the Hanes manual I had was unhelpful. The dealer told me it was a "special job" that had to be done in a shop.

Oct 04, 2012 | Cars & Trucks

1 Answer

Transmission issues


Typical Clutch Problem. Check to see if Clutch Linkage is Hydraulic or Mechanical. If Hydraulic then replace Clutch Slave Cylinder First.Bleed out air from Hydraulic line. if this doesn't fix it and or it has a Mechanical Clutch Linkage then Replace Clutch itself don't forget to get a new throw ou bearing and pack it with heavy duty grease otherwise in 20,000 miles you'll be doing it again. Thanks Keith

May 15, 2012 | 2004 Pontiac Sunfire

1 Answer

After changing transmission and clutch in 91 Wrangler, clutch goes to floor. Tried bleeding line but didn't work.


The clutch should go to the floor =) But if it's not disengaging the clutch disk, there's definitely a problem between the pedal and the clutch disk. I'm guessing you have a hydraulic clutch?

Apr 19, 2012 | 1991 Jeep Wrangler

1 Answer

I need to replace the clutch on 1997 vw jetta, does it have a cluth cable that would need to be replaced, or is it more complicated?


Most modern clutches have a hydraulic line. Emphasis on most, but this is a moot point for a production vehicle. What it should be is this: the clutch pedal is connected to a reservoir, which accepts DoT #3 brake Fluid (Usually), has a hydraulic line going down to the clutch, and either outside the transmission, or right inside it, is a slave cylinder that activates the actual clutch forks.

Jun 27, 2011 | 1997 Volkswagen Jetta

1 Answer

Manual 5 speed transmission clutch stuck. It was cold. Clutch itself is good. It appears to be a linkage prob of some sort. The haynes manual wont help because it covers too many diff trucks. mine is a 96...


Your truck has a hydraulic clutch, check to see fluid is full in the clutch master cylinder, and see if fluid is leaking at the line or the slave cylinder, line could have broke, or master/slave cylinder needs replaced.

Feb 08, 2011 | 1996 Ford F150 Regular Cab

2 Answers

How do you remove and old hydraulic line of a slave cylinder on a 1992 2WD 4.0L Cherokee so that the new one can be installed?


i dont think you are supposed to remove it. they come with a hose master and slave cyl all put together.
i did get one aprt once and i think there was a roll pin i pulled out to do it

Mar 20, 2010 | 1992 Jeep Cherokee Limited

2 Answers

2004 cavalier clutch pedal stays on floor,clutch not slipping. do i change clutch master cyl


Check for fluid leaks first along the line. Also check the mechanical linkage. Then try bleeding it. Changing the master cylinder is your last resort. That way you dont buy parts you don't need.

Nov 14, 2009 | 2004 Chevrolet Cavalier

1 Answer

The clutch fluid is leaking on my truck and it won't go into gear right.


You need to fix the Leak in your hydraulic system to your clutch on your transmission. The reason that your transmission is not going  in to gear right is that the fluid is to low to push the throw out bearing to disengage the clutch fully. 
Once the fluid get's too low, you'll not be able to disengage the clutch to put it in to gear or change gear.
Check the fluid level to your hydraulic clutch reservoir and fill to the right level and fix the leak in the hydraulic lines.
Good luck and hope this helps. Keep me posted, glad to help.

Jun 02, 2009 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...