Question about 1994 Chevrolet K1500

1 Answer

Why do my windsheild wipers not work

When I turn the switch to any of the settings the wiper motor just makes a weird nosie and the wipers dont move. I have replaced the wiper motor and it does the same exact thing.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

Problably you need to change the braces for the wiper,maybe they are touching in the metal inside and below the winshield,i had the same problem in a toyota tercel and i replace the braces,,,,,,there are a little gasket in the hole to make this adjust and it was broke

Posted on Feb 13, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the front wiper blades on a 1987 gmc jimmy so that i can remove the wiper motor


If you're talking about the wiper ARM pull the wiper away from the windshield and at the base of the arm you should see a little clip.
Get a little screwdriver or needle nose pliers and pull the clip away from the base. It will not come all the way off, when it is pulled away just jiggle the arm at the base while pulling up. It might take some jiggling but it will come off.

Feb 04, 2015 | GMC Cars & Trucks

2 Answers

1988 jeep cherokee,6 cylinder my front windsheild wipers dont work.fuse is good.the wiper motor makes a noise when its turned on.is there a relay that could be faulty?wiper switch is the same as the turn...


No relay in the circuit.
There is a delay module but if it fails that usually causes the wipers to stop in the middle of travel or only run on high.
And the switch is working if you hear noise coming from the motor. The wiper switch is not the same switch as the turn signals but it is near that assembly.
I would say if you have power to the wiper motor the motor is probably dead or something happened to the linkage to the arms.

Feb 27, 2013 | 1988 Jeep Cherokee

3 Answers

The wipers will not work in the daylight....when he starts the truck in the daylight the wipers will not come on.....at night when he is leaving work the wipers will work.....checked the fuses and replaced...


So what youre saying is the wipers work when the headlights are on
but the wipers dont work when the headlights are off?

I would suspect the turn signal switch is bad. I believe the switch on your S-10 controls
the wipers as well as switching from high beams to low beams. Since that switch is related
to the control of both headlights and wipers.

Could also be the headlight switch. The wiring harness from the turn signal switch plugs
into the headlights switch. I would replace the headlight switch first since you can get one
for around $25. Turn signal switch costs $150-$200. Maybe a little more or less for your vehicle.

Sep 10, 2011 | 1998 Chevrolet S-10 Pickup

1 Answer

Wiper on 2003 ford explorer. when turned on a noise comes from under dash and wipers dont work. they will work if I turn on switch and move the wipers, they will cycle once.


it sounds like the problem is the wiper motor if they work when you move them by hand.the motor probably has a bad spot in it,first try hooking up a jumper wire from the battery ground and the other end to the wiper motor body and make sure its a good ground at the motor.if the wipers work alright then permanently hook up a ground to the motor and body,as the motor will have a bad ground not allowing the wipers to work.

Apr 24, 2011 | Ford Explorer Cars & Trucks

1 Answer

I have a 1999 sl2 saturn and i need to know why the motor on the windshield wipers dont stop and go the other way so on and so forth


The motor continuously turns, it doesn't stop and back up. If your wipers got iced or stuck, they may have loosened the pivot nuts. Lift both wiper arms up off of the windsheild and then see if the wipers move correctly. If they do, shut off the wipers to let them "park." Loosen the nuts under the plastic cap at the base of the wiper arm, and set each arm to the park position, and then tighten the nut. These are made to slip so the motor doesn't get destroyed.

Mar 12, 2011 | 1998 Saturn SL

1 Answer

1999 pontiac windsheild wipers,motor makes a sound but they wont work,can move them manually


the wiper transmission they call it between the wiper motor and the wiper arms are stripped or broken
a replacement is needed

Mar 02, 2010 | 1999 Pontiac Grand Prix

1 Answer

Wipers dont work on intermitent thry work on high and low but stop on windsheild when pulsed this is a 2000 L 2


replacing the front wiper motor on the early L series is not difficult.
search around in fixya and you will find my instructions somewhere
at least twice. do not buy a replacement wiper motor from saturn, they are much cheaper through advance or autozone.

before you begin the repair, make sure your wiper switch is off and note the
wipers off position of the crank arm as stamped onto the wiper mount. this will make sense after you have the assembly out of the car and are replacing the wiper motor. if you ignore that mark then the wipers will be in the wrong position all the time.

Nov 27, 2009 | 2000 Saturn Ls 4dr Sedan

1 Answer

Wipers work when I manually move the stick, settings dont work


Turn the wipers on,and when they stop,peck on the wiper motor and see if they will come on.If they do replace the wiper motor,If they do not,replace the wiper switch.

Aug 29, 2009 | 1999 Hyundai Sonata

1 Answer

Wipers


If your just changing the wiper blades, turn the wipers on and when they get to the top, take the key out. They dont move back much but its enough to change them. If you want to take the arms off, lift the hood up and use a 13mm socket or wrench to loosen the nut and then wiggle the arm off. If you need to change the motor, unclip the black molding that the wiper arms are on and you have full access to the motor.

Apr 16, 2009 | 2000 Chevrolet Malibu

1 Answer

Y windsheild wipers don't move. I hear the


Possible stripped gears or the gears are not making contact.  I would replace the wiper motor.  If you can, and I am not sure, you might be able to replace just the gears.  But given how new the car is, I am sure it comes as an "all in one" unit.  It is possible to seatch www.car-part.com and see if there is a salvage yard around your area that has one cheap.

Mar 03, 2009 | 2006 Pontiac G6

Not finding what you are looking for?
Cars & Trucks Logo

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...