Question about Toyota Cars & Trucks

Open Question

Rear brakes toyota 1 ton dually

1 ton dually

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
robertcar
  • 2 Answers

SOURCE: changing rear drum brakes ona 1999 chevy dually

INSTALLATION PROCEDURE

ef3fd91.gif

  1. Install the parking brake lever (2).
  2. Install the spring washer (3). The concave side of the spring washer should face the parking brake lever.
  3. Install the pin (4).
  4. Install the retaining ring (16).
  5. Install the adjuster pin (12) in the shoe (15) so the pin projects 6.8 to 7.0 mm (0.268 to 0.276 inch) from the side of the shoe web where the adjuster actuator is installed.
  6. Apply brake lubricant or equivalent to the threads of the adjuster screw (14) and inside diameter and face of the socket (7). Adequate lubrication is achieved when there is a continuous bead of lubricant at the open end of the adjuster nut (10) and the socket (7) when the threads are fully engaged.
  7. Install the upper return spring (5).
    • Lay the shoes (1 and 15) on a clean, flat work surface in the position they will be in when installed on the backing plate.
    • The shoe with the parking brake lever goes to the rear of the vehicle.
NOTICE: Do not over-stretch the upper return spring. Damage can occur if it is stretched to more than 204.2 mm (8.04 inches) .

  1. Install the adjusting screw assembly.
  1. Lubricate the shoe pads on the backing plate with a thin coat of white lithium grease.
  2. Install the shoe and lining assemblies (1 and 15).
  3. Install the upper return spring (5).
  4. Install the adjusting screw assembly.
    • Do not damage the wheel cylinder boots.
    • Overlap the bottoms of the shoes so the upper shoe ends clear the wheel cylinder boots.
    • Make sure the upper shoe ends rest on the wheel cylinder piston ends.
    • Do not place the lower shoe web ends under the anchor plate until the lower return spring is installed.
NOTICE: Do not over-stretch the lower return spring. Damage can occur if it is stretched to more than 107.3 mm (4.22 inches) .

  1. Install the lower return spring (6).
    • Bring the ends of the shoe and lining assemblies (1 and 15) together over the anchor plate.
    • Hook the spring ends to the shoe web holes.
    • Spread the lower ends of the shoe and the lining assemblies to clear the anchor plate.
    • Position the shoes against the backing plate and release them.
    • Pull the spring into the groove at the bottom of the anchor plate.
  1. Connect the hold-down pins and the spring assemblies (8).
  2. Install the adjuster actuator (11) over the end of the adjuster pin (12) so the top leg engages the notch in the adjuster screw. NOTICE: Do not over-stretch the actuator spring. Damage can occur if it is stretched to more than 83 mm (3.27 inches) .
  3. Install the actuator spring (13). The free end of the adjuster actuator (11) must engage the notch of the adjuster nut.
  4. Connect the parking brake cable to the parking brake lever (2).
  5. Install the drum. Align the marks made during disassembly.
  6. Adjust the rear brakes.
  7. Install the tire and the wheel. Align the marks made during disassembly.

Posted on Jul 21, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: i need a rear brake

This link may help. Click on pictures to make them expand for better view. If not, let us know.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004c85c

Posted on Jan 07, 2009

Mike258
  • 1498 Answers

SOURCE: I need a color diagram for a 7 pin plug on my 2000

Hello,


Columns are Color, Function, Mark on the plug.

Seven wire Trailer plugs
:

Horse, stock or utility trailers:
White = Ground - 1
Blue = Electric Brakes - 2
Brown = Tail and clearance lights - 3
Black = Battery, aux power - 4
Yellow = Left turn/Brake - 5
Green = Right turn Brake - 6
Orange or Purple (not both) = Auxilliary or Reverse - 7

Recreational Vehicle:
White = Ground - 1
Blue = Electric Brakes - 2
Green = Tail and clearance lights - 3
Black = Battery, aux power - 4
Red = Left turn/Brake - 5
Brown = Right turn Brake - 6
Yellow = Auxilliary or Reverse - 7

Ground should be 10ga.
Others 14 ga

Best regards
Mike

Posted on Sep 09, 2009

  • 66 Answers

SOURCE: i need a diagram on front hub and brake assembly

8–Stud Rotor

  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Posted on Sep 16, 2009

  • 3 Answers

SOURCE: Replace brake shoes on rear of 93 Chevrolet

1. pull axles apx 6-10 bolts.
2. remove large holding nut
3. remove keeper\
4. remove 2nd nut
5. should now be able to pull off brake drum

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove a rear fiber glass fender on a 1 ton 2006 Silverado dually


Some of the newer vehicle use glue instead of spot welds or bolts. It has to be heated to like 500 degrees and then separated with a tool like a putty knife. Maybe use a heat gun if that's the case.

Jan 30, 2015 | 2006 Chevrolet Silverado

1 Answer

How do I get a 1987 ford F-350 custom 1 ton Dually owners manual


unless you know someone that had the same year of truck you will have to go to ford and have them order you one. not many people keep them if they no longer have the vehicle.

Oct 10, 2014 | Cars & Trucks

1 Answer

How do I replace rear bearings on a 2006 GMC Sierra 1 ton dually?


very carefully get a repair manual this will help you step by step

Sep 29, 2014 | Cars & Trucks

1 Answer

Need a diagram of 1999 chevy 1/2 ton 4x4 rear brake brackets


Go to you nearest auto part. Store. They will print one up for you or when you get the kit it will diagram with it

Mar 06, 2013 | 1994 Chevrolet K1500

1 Answer

How to replace rear brake pads 1986 Ford f350 1 ton dually


Hi Susan, I may be wrong but I believe that your truck has brake shoes on the rear. It's not an easy job so let me know if you would like to carry on with it or alternatively take it to someone else? Regards John

Jul 02, 2012 | Cars & Trucks

2 Answers

Brake squeal


You, Probably will, Brake Squeal is NOT a new problem.
Disc brake's have been Squealing since, They, became
factory installed on chevrolet in 1971. Before, that they,
were a option. In 72 they even had a bulleton how, to
FIX it. And, no it didn't work.
With That said, Any time you replace Brake pads you,
should always re-surface the Rotors.
Why? First you may start to notice a pulsation as the
pads ware (sometimes! ) The best way to avoid, brake
squeal is to manchine the Rotors put, the blue membrain
sealent on the back side of the pads. And hope that works!!
Some brakes Pads squeal JUST SQUEAL??
You, Could do the same Brake job the same as you did
this one and, they may NOT Squeal.WHY, I WISH I NEW. They
sell all types of STUFF to stop Brake noice DON'T waste your $$.

Jan 31, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

Replace brake shoes on rear of 93 Chevrolet dually? I can't find the process for a dually in any of the repair manuals I can find in local part stores.....


1. pull axles apx 6-10 bolts.
2. remove large holding nut
3. remove keeper\
4. remove 2nd nut
5. should now be able to pull off brake drum

Dec 13, 2009 | 2001 Chevrolet Silverado 3500

1 Answer

I need a diagram on front hub and brake assembly for 1999 dodge 1 ton dually 2 wheel drive. the front brake rotor is warped i need to replace it


8–Stud Rotor
  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Sep 16, 2009 | 2000 Dodge Ram 3500

1 Answer

I need a color diagram for a 7 pin plug on my 2000 chevrolet 1 ton dually


Hello,


Columns are Color, Function, Mark on the plug.

Seven wire Trailer plugs
:

Horse, stock or utility trailers:
White = Ground - 1
Blue = Electric Brakes - 2
Brown = Tail and clearance lights - 3
Black = Battery, aux power - 4
Yellow = Left turn/Brake - 5
Green = Right turn Brake - 6
Orange or Purple (not both) = Auxilliary or Reverse - 7

Recreational Vehicle:
White = Ground - 1
Blue = Electric Brakes - 2
Green = Tail and clearance lights - 3
Black = Battery, aux power - 4
Red = Left turn/Brake - 5
Brown = Right turn Brake - 6
Yellow = Auxilliary or Reverse - 7

Ground should be 10ga.
Others 14 ga

Best regards
Mike

Apr 15, 2009 | 2000 Chevrolet 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...