Question about 1995 Jaguar XJ6

2 Answers

Wheel locknut key

I have a xj6 sport lost the key to get off locking wheel nuts what can i do

Posted by on

  • thomasmc88 Dec 03, 2008

    i have a ford focus 03 plate, i have lost the wheel locknut key.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

If you know the key code which is usally on the key, you should be able to get one from the dealers no problem. next garage is an option, but then again you can DIY, you can purchase wheel locking nut remover cheap eg Halford

Posted on Jan 14, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 21,981 Answers

Take it to a tyre shop they should have a universal tool for removing them

Posted on Nov 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

How do I remove wheel Lock nut on 1999 Isuzu Trooper if lock key has lost?


we cant see it of the 100s made.
go to any tire./wheel store and ask them to fix this.
or drill yours out. (some you can, no photo no joy here)

Aug 17, 2014 | 1999 Isuzu Trooper

1 Answer

Diagram of front hub and axle 1994 Ford explorer 4 wheel drive.


Here you go.
Notes:
  • To prevent damage to the spindle during removal, remove adjusting nut locking key from spindle keyway under adjusting nut prior to nut removal.
  • A slight movement of the nut will loosen the locking key so that a magnet can be used for removal.
  • During the front wheel bearing adjustment procedure, align the closest two holes in the wheel bearing adjusting nut with the center of the spindle keyway slot.
  • Advance the nut to the next hole if required. To ensure proper wheel retention, install adjusting nut locking key in alignment with spindle keyway and insert into locknut holes.
  • The double humped portion must be completely seated and flush with the locknut assembly.
  1. Raise and support front of vehicle.
  2. Remove wheel and tire assembly.
  3. Remove lug nut stud retainer washers, then the locking hub assembly.
  4. Remove snap ring from end of spindle shaft.
  5. Remove axle shaft spacer, needle thrust bearing and bearing spacer.
  6. Remove cam assembly, thrust washer and needle thrust bearing from wheel bearing adjusting nut.
  7. Remove the adjusting nut lock key, then the nut.
  8. Remove the rotor and replace the bearings, races and seal as necessary.
  9. Torque nut to 35 ft lb while rotating hub and rotor assembly.
  10. Back off adjusting nut 1/4 turn, then torque nut to 16 inch lbs.
  11. Align nearest hole in adjusting nut with center of spindle keyway slot. If necessary, advance nut to the next hole.
  12. Install locknut needle bearing, thrust washer and cam assembly.
  13. Install bearing thrust washer, needle thrust bearing, axle shaft spacer and snap ring.
  14. Install locking hub assembly and retainer washers, then the wheel and tire assembly.
  15. Ensure wheel endplay on spindle is 0.000-0.003 inch.

2_13_2012_8_39_39_pm.gif

Feb 13, 2012 | 1994 Ford Explorer Limited

1 Answer

How do I replace front rotors/brake pads 2002 B4000 2wh dr


11_30_2011_3_48_02_pm.jpg


Fig. Exploded view of the wheel bearing adjusting nut and related components-automatic locking hub shown

Loosen the wheel bearing locknut using a 2 3/8 inch (60.3mm) hex socket, such as Hex Locknut Wrench T70T-4252-B.


11_30_2011_3_48_28_pm.jpg

Fig. An oversize socket is needed to properly adjust the wheel bearing-automatic locking hub shown

Tighten the inner locknut to 35 ft. lbs. (47 Nm) to seat the bearings.

Spin the rotor and back off the inner locknut 1/4 turn (90 degrees). Retighten the locknut to 16 inch lbs. (1.8 Nm).

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 30, 2011 | Cars & Trucks

2 Answers

Mazda B4000 2 WD, What is the Front wheel bearing torque after I replace the rotors


11_30_2011_3_48_02_pm.jpg


Fig. Exploded view of the wheel bearing adjusting nut and related components-automatic locking hub shown

Loosen the wheel bearing locknut using a 2 3/8 inch (60.3mm) hex socket, such as Hex Locknut Wrench T70T-4252-B.


11_30_2011_3_48_28_pm.jpg

Fig. An oversize socket is needed to properly adjust the wheel bearing-automatic locking hub shown

Tighten the inner locknut to 35 ft. lbs. (47 Nm) to seat the bearings.

Spin the rotor and back off the inner locknut 1/4 turn (90 degrees). Retighten the locknut to 16 inch lbs. (1.8 Nm).

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 27, 2011 | 2007 Mazda B4000

1 Answer

I've changed rotors before but never on a 4 wheel drive. Could you tell me how to on a 1989 ford ranger?


Brake Rotor (Disc) - REMOVAL & INSTALLATION
  1. Loosen the wheel lug nuts.
  2. Jack up the front of the vehicle and support on jackstands.
  3. Remove the wheel and tire.
  4. Remove the brake caliper assembly as described earlier in this section, but do not disconnect the brake hose.
  5. Suspend the caliper assembly by a piece of wire. Do not allow it to hang by the brake hose.
  6. Follow the procedure given under wheel bearing removal in Suspension and Steering for models with manual and automatic locking hubs (lines down).
New rotor assemblies come protected with an anti-rust coating which should be removed with denatured alcohol or degreaser. New hubs must be packed with EP wheel bearing grease.
  1. Installation is the reverse of the removal procedure.


Front Wheel Bearings - REMOVAL & INSTALLATION
(see Figure 1 )


zjlimited_533.gif

Fig. 1: Inspect the bearings for abnormal wear and/or damage



With Manual Locking Hubs
(see Figures 2 through 17)

  1. Raise the vehicle and install jackstands.
  2. Remove the wheel and tire assembly.
  3. Remove the retainer washers from the lug nut studs and remove the manual locking hub assembly from the spindle.
  4. Remove the snapring and spacer from the end of the spindle shaft.
  5. Remove the outer wheel bearing locknut from the spindle using 4 prong spindle nut spanner wrench, T86T-1197-A or equivalent. Make sure the tabs on the tool engage the slots in the locknut.
  6. Remove the locknut washer from the spindle.
  7. Remove the inner wheel bearing locknut from the spindle using 4 prong spindle nut spanner wrench, T86T-1197-A or equivalent. Make sure the tabs on the tool engage the slots in the locknut.
  8. Remove the outer bearing cone and roller assembly from the hub. Remove the hub and rotor from the spindle.
  9. Using seal removal tool 1175-AC or equivalent remove and discard the grease seal. Remove the inner bearing cone and roller assembly from the hub.
  10. Clean the inner and outer bearing assemblies in solvent. Inspect the bearings and the cones for wear and damage. Replace defective parts, as required.
  11. If the cups are worn or damaged, remove them with front hub remover tool T81P-1104-C and tool T77F-1102-A or equivalent.
  12. Wipe the old grease from the spindle. Check the spindle for excessive wear or damage. Replace defective parts, as required.
zjlimited_534.gif

Fig. 2: Before beginning the wheel bearing removal, and after the outer hub is removed, wipe off any excess grease

zjlimited_535.gif

Fig. 3: After the grease is wiped off, remove the axle shaft snapring ...

zjlimited_536.gif

Fig. 4: ... then pull the splined spacer from the axle shaft end

zjlimited_537.gif

Fig. 5: Use a 4 pronged socket to loosen the outer wheel bearing locknut ...

zjlimited_538.gif

Fig. 6: ... then remove the outer locknut

zjlimited_539.gif

Fig. 7: Remove the lockwasher from behind the outer locknut ...

zjlimited_540.gif

Fig. 8: ... then loosen and remove the inner locknut-note the lockwasher engagement pin (arrow)

zjlimited_541.gif

Fig. 9: While pushing inwards on the rotor/hub assembly, remove the outer wheel bearing ...

zjlimited_542.gif

Fig. 10: ... then pull the rotor/hub assembly from the spindle, taking care not to scratch the bearing cups in the hub

zjlimited_543.gif

Fig. 11: Pry out the grease seal on the back of the rotor/hub assembly ...

zjlimited_544.gif

Fig. 12: ... then remove the inner wheel bearing. Thoroughly clean and inspect all of the parts for wear or damage





continue...

Jul 29, 2011 | 1989 Ford Ranger

2 Answers

I have a 1999 Mitsubishi Montero Sport 3.0L V6 engine It has one lug nut lock on each of the stock rims and I have no key to get them off to fix my brakes. I need to know what is the specific size and type...


finding a key will be most difficult, you can find a removal tool from a specialy tool supplier like snapon, its a reverse screw type nut that will grip the outside of the lock

Oct 16, 2010 | 1999 Mitsubishi Montero Sport

1 Answer

I have a problem taking the wheel off as there are lock nuts on the nuts themselves and i dont know how to remove them, please can you help


if you havnt got the locknut key,then use an old socket and hammer it onto the nut head until it jams on then undo,before you take it off fully, hit it sideways to remove the socket for the next nut.you will destroy the socket,the other way is to use a nut splitter.

Oct 14, 2010 | Renault Fuego Cars & Trucks

1 Answer

Front brake rotor on 1992 Ford Ranger 4wd with auto lock in


With Automatic Locking Hubs
  1. Raise the vehicle and install safety stands.
  2. Remove the wheel lugnuts and the wheel and tire assembly.
  3. Remove the retainer washers from the lugnut studs. Remove the automatic locking hub assembly from the spindle.
  4. Remove the snap ring from the end of the spindle shaft.
  5. Remove the axle shaft spacer
  6. Being careful not to damage the plastic moving cam or thrust spacers, pull cam assembly off the wheel bearing adjusting nut and remove the two plastic thrust spacers from the adjusting nut. CAUTION: Do not pry on the plastic cam or thrust spacers during removal. Prying may damage the cam or spacers.
  7. Using a magnet, remove the locking key. NOTE: If required, rotate the adjusting nut slightly to relieve pressure against the locking key, before the key can be removed. CAUTION: To prevent damage to the spindle threads, look into the spindle keyway under the adjusting nut and remove the separate locking key before removing the adjusting nut.
  8. Loosen the wheel bearing adjusting nut from the spindle using a 2-3/8 inch Hex Locknut Wrench T70T-4252-B or equivalent.
  9. While rotating the hub and rotor assembly, tighten the wheel bearing adjusting nut to 47 Nm (35 ft lb) to seat the bearings. Spin the rotor and back off the nut one-quarter turn (90 degrees).
  10. Retighten the adjusting nut to 1.8 Nm (16 in lb) using a torque wrench.
  11. Align the closest lug in the wheel bearing adjusting nut with the center of the spindle keyway slot. Advance the nut to the next lug if required. Install the separate locking key in the spindle keyway under the adjusting nut. WARNING: Extreme care must be taken when aligning the spindle nut adjustment lug with the center of the spindle keyway slot to prevent damage to the separate locking key. The wheel and tire assembly may come off while the vehicle is in motion if the key is damaged.
  12. Install the two thrust spacers and push or press the cam assembly onto the locknut by lining up the key in the fixed cam with the spindle keyway. CAUTION: Extreme care must be taken when aligning the fixed cam key with the spindle keyway to prevent damage to the fixed cam.
  13. Install the axle shaft spacer.
  14. Clip the snap ring onto the end of the spindle shaft.
  15. Install the automatic locking hub assembly over the spindle by lining up the three hub assembly legs with three pockets in cam assembly. Install the retainer washers.
  16. Install the wheel and tire assembly. Install and tighten lugnuts to 135 Nm (100 ft lb).
  17. Make sure the final end play of the wheel on the spindle is 0.00-0.08 mm (0.000-0.003 inch). the maximum torque to rotate the hub is 2.8 Nm (25 in lb).

Jul 27, 2009 | 1992 Ford Ranger

Not finding what you are looking for?
1995 Jaguar XJ6 Logo

Related Topics:

369 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...