Question about 2002 Ford Focus

Open Question

Location of knock sensor in 1.6 zetec se - 2002 Ford Focus

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jturcotte
  • 7768 Answers

SOURCE: i want to know where is the knock sensor is

It's under the intake manifold. Please let me know if you have more questions.

  1. Disconnect the battery ground cable.
  2. Remove the intake manifold.
  3. Remove the knock sensor (KS).
  4. Remove the retaining bolt.
  5. Remove the knock sensor.
  6. Installation is the reverse of the removal procedure. Tighten the sensor to 15 ft. lbs. (20 Nm).

93678f7.gif

Posted on Oct 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi changed my thermostat on this ford focus 1,6 2001 and since then the heater is red hot but the temp gauge stays on cold cant find what to do by the way its a zetec se engine


check to see if you knocked the wire off of the sensor. if not you might have trapped air in system and will have to open bleader and fill with water to top

Jun 04, 2015 | Ford Cars & Trucks

2 Answers

Bad knock sensor symptoms


If your original engine didn't have a knock sensor, but the new one does, don't worry about it. You can safely remove it or just ignore it.

Oct 20, 2013 | Cars & Trucks

2 Answers

Where is the knock sensor located on a 2000 saab 93 se


knock sensor located on the side cylinder block below intake manifold.

Nov 27, 2012 | Cars & Trucks

1 Answer

I want to know where is the knock sensor is located on my 2000 ford focus se


It's under the intake manifold. Please let me know if you have more questions.
  1. Disconnect the battery ground cable.
  2. Remove the intake manifold.
  3. Remove the knock sensor (KS).
  4. Remove the retaining bolt.
  5. Remove the knock sensor.
  6. Installation is the reverse of the removal procedure. Tighten the sensor to 15 ft. lbs. (20 Nm).

93678f7.gif

Oct 28, 2010 | 2000 Ford Focus

1 Answer

Knock sensor replacement ....2003 kia rio....emissions ...obd II....failure...need to pass inspection...failure code P0325 (Knock sensor 1 circuit malfunction)....where vis the knock sensor located on a...


Turn ignition off. Disconnect knock sensor 3
-
pin harness connector. Locate knock sensor, on cyli
nder block.
On Optima 2.7L engine, sensors are located on both
sides of cylinder block. . Remove knock
sensor from cylinder block. To install, reverse rem
oval procedure.

Mar 19, 2010 | 2003 Kia Rio

1 Answer

Where is the knock sensor driver side for 2001 pontiac grand prix


Hello! Here is a picture of the location of the front knock sensor for a 3.8 liter V6 3800 Series II (97-03)
(Please note that the engine is upside down on the stand)
There are 2 knock sensors on this engine, one on the front (as shown), and another in the rear. There isn't one on the driver's side, per se.

0038e37.jpg

I recommend that you let the vehicle cool down before beginning this process. To remove this you will need a drip pan, as coolant will leak from the engine when the sensor is removed. You will need a deep well 22mm socket and torque wrench.

1. Jack up and support the vehicle on jack stands so that you can work from underneath the vehicle. Be sure to apply your emergency brake.
2. Identify the knock sensor location and remove the electrical connector on the bottom.
3. Using the deep well socket, remove the sensor from the block. Do not position yourself direcly underneath this, as coolant will begin to flow immediately from the sensor's location.
4. Your new knock sensor should come pre-coated with sealant/threadlock, just install it and tighten by hand until snug.
5. Torque the sensor to 14 ft lbs.
6. Replace the electrical connector.
7. You should flush the entire coolant system to be sure to remove any air pockets, and then refill.


Hope this helps and thanks for using FixYa!

Oct 01, 2009 | 2001 Pontiac Grand Prix

2 Answers

Location of knock senor on 97 maxima se


Your knock sensor is located Under the hood, center, front engine area, below intake manifold, mounted on block.


A defective knock sensor may cause engine detonation or reduced spark advance and fuel economy. When a knock sensor is removed and replaced, the sensor must be tightened to its specified torque. If the knock sensor is installed tighter than it should be, it may become too sensitive and provide an excessively high voltage signal, resulting in more spark ****** than required. When the knock sensor is installed looser than it should be, the knock sensor signal will be lower than normal, resulting in engine detonation.

To replace the knock sensor:
  • Disconnect the knock sensor wiring connector.
  • Then, unscrew the sensor.
  • Remove the knock sensor.
  • Reverse the procedures to install the part.

May 15, 2009 | 1997 Nissan Maxima

Not finding what you are looking for?
2002 Ford Focus Logo

Related Topics:

598 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...