Question about 2001 Hyundai Tiburon

Open Question

Ball joint specifications

All ball joint specs and checking procedure please

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Upper ball joint torque specs 2002 explorer xls 4x4 4.0L v6 gas


Douglas, 90 lb-ft is ball joint nut torque.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Upper Control Arm and Ball Joint 2002 05 Ford Explorer...

Apr 02, 2016 | 2002 Ford Explorer

2 Answers

What are the torque specs for the 3 lower ball joint mounting bolts and also the castle nut torque


You can easily find those specs, and a lot more R&R procedures, wire diagrams, capacities, etc,. if you just go to autozone.com, register for free and list your make, year, model, and engine size if asked. Easy and quick, you can list as many vehicles as you want, then find specific information for it.

You would likely find the information under "vehicle repair guides", that's not a common torque spec., so it may be listed under the repair guide for the ball joints. I have found autozone not as good as a Haynes repair manual, but better than nothing. Plus, it's a handy place to check prices for parts you need.

Apr 12, 2015 | 2000 Nissan Pathfinder

2 Answers

What is differential fluid


differential fluid is typically called 80w 90 (or similar designation based on manufacturer specs.) but is very different from the grease used in ball joints. you should check your owner's manual for specific specifications, but typically a good NLGI listed wheel bearing grease applied through the grease fittings on the ball joints will properly lube the ball joints

Dec 29, 2012 | 2000 Jeep Grand Cherokee

1 Answer

Torque on front ball joints 2000 Honda Passport 2 wheel drive


Lower ball joint specs:
Torque the ball joint-to-control arm nuts/bolts to 85 ft. lbs. (115 Nm). Torque the castellated nut to 108 ft. lbs. (147 Nm).

Upper ball joint specs:
Tighten the mounting bolts to 42 ft. lbs. (57 Nm) and the castellated nut to 72 ft. lbs. (96 Nm).

Feb 28, 2011 | 2000 Honda Passport

1 Answer

2005 malibu maxx ball joint and lower control arm torque specs


A Ball Joint Can Usually Be Replaced Without Removing The Control Arm From The Vehicle. Place The Vehicle On Jack Stands. Remove The Shock Absorber And Install A Spring Compressor on The Coil Spring.Remove The Nut Securing The Ball Joint To The steering Knuckle And Separate The Knuckle And Then Joint. The Ball Joint Should Be Pressed,Riveted,Bolted,Or Screwed Into The Control Arm.A Service Manual Will Give The Details For The Specific Make And Model Vehicle.

Apr 09, 2010 | 2005 Chevrolet Malibu Maxx

1 Answer

How do you put in a ball joint in a 2001 sebring convertible


It depends on exactly which ball joint of the 3 per side your changing, but here are the details.

COMPRESSION LOWER ARM & LATERAL LOWER ARM ASSEMBLIES
Removal
1. Loosen compression lower arm ball joint nut. Using steering linkage puller, separate ball joint and
knuckle. Remove nut, bolts and compression lower arm assembly. Remove dust cover.
2. Remove stay. Remove shock absorber lower mounting bolt. Loosen lateral lower arm ball
joint and knuckle nut. Using steering linkage puller, separate ball joint and knuckle. Remove nut, bolt and
lateral lower arm assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for compression lower arm ball joint is 4-22 INCH lbs. (0.5-2.5
N.m) for 2000 models. On 2001 models, breakaway torque is 22-54 INCH lbs. (2.5-6.1 N.m). Ensure
breakaway torque for compression lateral lower arm ball joint is 13 INCH lbs. (1.5 N.m). Check compression
lower arm, lateral lower arm, dust covers, and bushings for damage and wear.
Installation
To install, reverse removal procedure. Use NEW ball joint nuts. Lubricate lip and inside of dust cover with
multipurpose lubricant. Using installer, install dust cover. Check front wheel alignment.
UPPER ARM ASSEMBLY
Removal
Using steering linkage puller, loosen upper arm ball joint and knuckle nut. Remove self-locking nut. Remove upper arm and upper arm shaft assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for upper arm ball joint is 3-13 INCH lbs. (0.3-1.5 N.m).
Replace upper arm assembly when measured value exceeds specification. Check upper arm, dust cover, and
bushings for damage and wear.
Installation
1. To install, reverse removal procedure. Use NEW self-locking nuts. Lubricate lip and inside of dust cover
with multipurpose lubricant. Using Ball Joint Installer (MB990800), install dust cover.
2. Ensure upper arm shaft assembly is installed at indicated angle. Verify upper arm shaft
assembly installation. Check front wheel alignment.

Once you have the correct arm off and a replacement joint (if available, some are not serviceable and require the arm to be replaced) then you will need a press or a ball joint press to change the joint. Such as
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38335

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46389

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66958

or http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46967

Mar 17, 2010 | 2002 Chrysler Sebring

1 Answer

My trw lower ball joint came with torque specs for the mounting bolts to 15ft.lbs each.. My trw upper ball joint came with no specs for the mounting bolts which are smaller bolts than the lowers, how do i...


I've replaced many ball joints, and never used a torque wrench. Just make them tight. If yours are the type with cotter pins, then you make it tight and slip in the cotter pin.

Sep 24, 2009 | 1996 GMC Jimmy

3 Answers

Ball joint installation


Go with what the ball joint specs. Besides only 2 ft.lbs. on a ball joint won't make a difference. But the parts recommendation should be used.

Sep 23, 2009 | 1996 GMC Jimmy

1 Answer

Lower ball joint removal from a-arm


The entire control arm is supposed to be replaced on those when ball joint fails. Did you manage to buy another ball joint only?

Apr 26, 2009 | 2001 Nissan Altima

Not finding what you are looking for?
2001 Hyundai Tiburon Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...