Question about 2002 GMC Envoy

Open Question

How to replace third brake light gmc envoy

How do you dismantle and remove the old third brake light on a 2002 gmc envoy?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: Replace the thermostat on 2002 GMC Envoy

4.2L Engine the thermostat and the neck where the hose goes on is one unit $25 at autozone

  1. Remove the necessary coolant from the radiator.
  2. Remove the alternator, Loosen the outlet hose clamp at the thermostat housing. Remove the outlet hose from the thermostat housing.
  3. Remove the thermostat housing bolts.
  4. Remove the thermostat housing from the engine block.
  5. Clean all of the surfaces of the thermostat housing.
  6. Clean the sealing surface of the engine block.

Posted on Dec 29, 2008

Ad
  • 250 Answers

SOURCE: battery removal on a 2004 GMC Envoy

The battery is on the right side behind the fuse box. You need a metric set to undo the 3 screws. Theres one that attaches to the body, one to the bar that goes along the top, and theres one on the left side below the vacuum hose and air induction. After you've taken out those three, you should lift the whole thing out(battery and shroud) together. It's hard to take the shroud off before you lift the battery out. After that, you have to pry the shoud off the battery. The two terminals in the back make it hard. Then just go to any auto parts store and they'll give you a new one. 

Posted on Jan 28, 2009

hi99ins
  • 123 Answers

SOURCE: 2002 GMC Envoy Brake Lights Don't Work

It involves a little tricky manouvering under the dash to reach the switch and you need to be very aware of the orientation when fitting. PLEASE BE AWARE that you are messing with the brake pedal and if you fit this part incorrectly you could interfere with the brake pedal travel and cause a dangerous driving situation. Only fit this part once you have fully inspected the part to be removed, and preferably look at a workshop diagram. Some switches are easy some are not. Most take me 10-15 mins.

Posted on Jan 07, 2009

  • 104 Answers

SOURCE: Need firing order diagram for 2002 gmc envoy

one, five, three, six, two, four

The plastic intake should have this sequence molded into it somewhere, and even the corresponding cylinder numbers in front of their respective holes. Have fun, and thanks for posting on Fixya.com

Posted on Mar 20, 2009

dsacco86
  • 1077 Answers

SOURCE: I need to know how

It would be to hard to tell and show you over the computer.
The best and easiest way for you is to buy a Chilton manual for your car at the autoparts store. The book runs about $20
This book is a do-it-yourself bible. It will show you everything you need to know on how to do maintenance and repair on your vehicle.

Posted on Apr 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the tail light fuse?


The tail light fuse is under the rear seat on the drivers side.

Jan 17, 2016 | 2003 GMC Envoy

1 Answer

I have a 2005 GMC Envoy. Have tail lites but no brake lites. Third lite on top works whet brakes applied


Since the high mounted brake light works you know that the brake light switch is working. Now you need to check the brake light bulbs in the rear tail light assemblies. The brake lights are separate from the tail light (parking or running lights). There are two screws that hold the rear light assemblies in place.

Mar 13, 2011 | 2005 GMC Envoy

3 Answers

2004 Envoy brake lights do not come on when you push brake. The bulbs are fine


This is the part you will need to replace.
http://cgi.ebay.com/ebaymotors/AC-Delco-BRAKE-LIGHT-SWITCH-gmc-ENVOY-2003-2002-2006-/250579604910

Mar 12, 2010 | 2005 GMC Envoy Xl

4 Answers

Brake lights won't work. tail lights do. I


need to know if your third brake light up high is working or not.if it isn't,you need to check the brake light switch on the brake pedal with a test light,one side hot all the time,the other side should turn hot when brake pedal is pushed.

Jan 19, 2010 | 2002 GMC Envoy XL

1 Answer

Where is the interior fuse panel on my 2002 gmc envoy? Thanks!


There are two fuse boxes on a 2002 Envoy One under the Rear seat on the drivers side and one under the hood on the drivers side.

Mar 19, 2009 | 2002 GMC Envoy

1 Answer

Brake problem


Switch on brake pedal stuck due to dust etc. Many new cars have a safety feature that allow the brake-lights to come on if the brake lever is depressed, even when the ignition is switched off.
If you can get to the switch, a good cleaning with methylated spirits and a small brush should allow it to move freely again. Good luck.

Mar 09, 2009 | 2002 GMC Envoy

1 Answer

How to remove and replace upper brake light on 2002 GMC Yukon.


Problem, which has been fixed, was with a 2002 Yukon, not a 2004 Escalade. Removing two screws below the upper or third brake light allows you to remove and replace the LED assembly.

Feb 17, 2009 | 2004 Cadillac Escalade

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

1 Answer

2002 GMC Envoy Brake Lights Don't Work


It involves a little tricky manouvering under the dash to reach the switch and you need to be very aware of the orientation when fitting. PLEASE BE AWARE that you are messing with the brake pedal and if you fit this part incorrectly you could interfere with the brake pedal travel and cause a dangerous driving situation. Only fit this part once you have fully inspected the part to be removed, and preferably look at a workshop diagram. Some switches are easy some are not. Most take me 10-15 mins.

Jan 07, 2009 | 2004 GMC Envoy

Not finding what you are looking for?
2002 GMC Envoy Logo

Related Topics:

456 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...