Question about Cars & Trucks

1 Answer

No power to starter

Starter, battery, fuses check ok.....all lighting, alarm work when ignition is turned but started wont turn

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Relay needs changed out

Posted on Feb 13, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: 1996 chevy s10 will not

check the crankshaft sensor

Posted on Aug 14, 2008

  • 1 Answer

SOURCE: Jimmy won't start

We have the same problem with our 97 Jimmy, The radio and blower worked but none of the dash lights would come on. Had one repair shop look at it and they could not figure it out. Just bought it on Dec. 31st. 2008 and 2wks later it started happening. Took back to the dealer and they didn't think that it was the ignition switch, recommended another repair shop and they only had it for about an hour and called and said that it was the ignition switch. We ran a jumper wire from a hot link in the fuse box too the motor fuse, both on the top side and all the lights on the dash came on and it started right up. Hope that this helps.

Posted on Jan 28, 2009

  • 79 Answers

SOURCE: no power to starter 2004 chevy tahoe

Hi
It could be your neutral safety switch. It could be the starter relay which is located in the fuse panel box. It could be the smaller wire going to the starter could be loose or corroded.

Posted on Apr 01, 2009

ZJLimited
  • 17970 Answers

SOURCE: My 1999 nissan altima won't

1999 Nissan/Datsun Altima 2.4L SFI DOHC 4cylNo Start when Ignition key ON, check "inspect" this items:
1. Ignition Switch: Improperly Connected or Faulty Ignition Switch.
2. Battery: Battery Discharged or Faulty or Coroded, Broken, Shorted or Poorly Connected Battery Cable.
3. Solenoid Switch: Starter Solenoid Switch Faulty.
4. Starter Starter Motor Faulty.
5. Wireset: Worn or Damaged Spark Plug Wires.
6. Coil -Ignition-: Faulty Ignition Coil.
7. Distributor Cap: Loose, Cracked or Worn Distributor Cap.
8. Spark Plug: Incorrectly Gapped or Fouled Spark Plug(s).
9. Distributor Cap and Rotor Kit: Loose, Cracked or Worn Distributor Cap.
10. Carburetor: Worn, Faulty or Damaged Carburetor.
11. Fuel Pump Faulty Fuel Pump.

Send news about this.

Posted on Sep 02, 2009

  • 128 Answers

SOURCE: My 98 jeep grand cherokee wont start.

fuse 8 40a supplies power to starter relay and ignition switch, to close the starter solenoid and engage the starter which draws directly from the battery. check to see that the starter relay is closing, if not ensure that the park neutral switch is not faulty (open circuit), it provides path to close relay (ground side) on the 85 - 86 terminals. if the starter relay does not close the starter will not run. if you have a spare relay swap out the relay for a quick fix attempt. hope this helps

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 plymouth voyager wont start and nothing work the windows wont go down the lock and unlock button does nothing idk what the problem is i had the battery tested and the battery is fine what would cause...


Nothing works? How about the headlights, do they work? If yes, then start checking all fuses in the Power Distribution Center or Box under the hood. If no, then look for a bad maxi-fuse in the PDC, and check for a bad fusible link between the battery and the PDC. The battery positive cable goes to the starter, but a pigtail lead off the positive would go to the PDC, to distribute power to all the various circuits on the car.
When you turn the key to on, does the dash light up? If yes, at least power is getting to, and going through the ignition switch. One could then check for power on the starter solenoid wire when key was held in crank or start position.
If nothing when turning key to on-no dash lights, nothing-then check for an ignition fuse in the PDC. If fuse is good check for power being available at the ignition switch connector. If no power there, check wiring between PDC and the ignition switch-if power is up to the switch, but nothing happens with key on, no dash or warning lights, then could have a bad ignition switch.
It just sounds like a maxi-fuse has blown, or a bad fusible link. Good luck.

Mar 18, 2013 | Cars & Trucks

2 Answers

Alarm on 2004 kia spectra wont let me start car


If the alarm is aftermarket I would remove it , I see this problem several times a month , take a test light and test for power at the starter signal wire while someone turns the key to crank this is the small gauge wire going into starter,if there is no power at this wire it will not crank ,if you momentarily apply voltage to the starter signal wire it will crank( also check starter signal fuse)(most alarm systems have a starter interrupt system ,and the aftermarket alarms fail after a few years) Alot of people believe there alarm is factory because it was there when they bought it new but dealer do add alarms that are aftermarket to please there insurance companies

Nov 19, 2017 | Kia Spectra Cars & Trucks

1 Answer

1500 Ram wont start, no crank no click nothing. Air cond and dash lights work just fine just wont start. Battery is ok tried to jump, no luck, put in different battery no luck.


First thing is to check is the ignition fuse/relay under the hood for a blown fuse or bad relay. If everything is ok then set parking brake with truck in park/netural and have someone to turn the ignition over to start and at the same time use a test light to check for fire at the starter solenoid. If no fire then the ignition switch or netural switch on transmission is causing the problem. If you do have power to the starter solenoid then the problem would be either the solenoid or the starter drive locked up on the flywheel. Be sure to remove the negative wire from the battery if you need to remove the starter. Hope this will help you.

Jun 02, 2010 | 2008 Dodge Ram 1500 2WD

2 Answers

94 z wont start


You will have to check, at the starter, for power to the SMALL wire on the starter solenoid (which is on the starter) when turning the ignition switch to start.
If there is power to this wire ( usually purple ) and power at the LARGE cable ( from the battery ) at the starter end.....you need a starter.

If you do not have power at the small wire at the solenoid with the key in start position and battery power is OK.....check the safety neutral switch.Moving the shifter around a little can sometimes allow the car to start if the neutral switch is worn.

A new battery does not always mean a fully charged battery.
Try a boost from another car before testing the starter for power.

The battery cables need to be clean and tight....and check the ground to the engine as well.

Everything else may work OK with bad connections,they don't use the power the starter needs to turn the engine over.

Sep 08, 2009 | 1994 Chevrolet Camaro

2 Answers

02 chevy trailblazer 4.2l car wont start installed new starter still wont crank or start test fuses all are good lights and horn operate but no start could it be the ignition switch not giving power to the...


You need to establish that you have 12v in the battery and that all connections are clean and secure. Lights horn etc do not give you voltage verification...your starter uses more amperage than anything else in the car. Once you are certain that everything is OK, check for 12v at the small wire on the starter with the key turned to start. If no volts, check the neutral safety switch or clutch switch Then check ignition switch for power in/out.

Jun 09, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

I can not find the neutral safety switch on a 2000 buick park ave


Any chance your vehicles have a security/alarm system. Disconnecting battery on some, will arm it sometimes & not allow it to run. Using key to unlock door, on driver & passenger side have been known to work on some vehicles, but if not, a call to dealer should help.

May 31, 2009 | 2000 Buick Park Avenue

1 Answer

I have telstar tx5 ghia 1990 2,2l 4 cilind automatic, power everithing,car is done 240000.yus wont start one mornig doing klik didn t start and couple time kliking alnaser (starter) and i have used cable ...


Hi
Easiest test is to reconnect jumper cables and switch lights on, if these work and no noise AT ALL from starter, NO clicking at all then could be the jumper cables are too light like most are. Try 2 sets of jumper cables. Ensure that the cables are correclty applied, Red to Red and the black is the last connection to a good steel part on your engine, NOT the battery.Always ensure the car being used to jump from is running at all times while cables are connected.When it starts remove this one FIRST also.

Cheers cbacer

Apr 30, 2009 | Mazda 626 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...