Question about Jeep Cars & Trucks

Open Question

2000 ford crown vic hood release inside car is not working how do i get hood open?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 599 Answers

SOURCE: 2000explorer hood release

sit on hood or pound on it (center front) while assistant pulls cable release from inside..then adjust stops so it wont happen again...have you had a fender bender recently?

Posted on Nov 07, 2008

Ad
  • 261 Answers

SOURCE: Ford Crown Vic p0300 random cylinder misfire

take a look at the EGR valve it could be either vacum controlled or electronic either way what seems to be the problem is that the valve is stuck in the open position until the engine warms up you can gently tap the egr valve with a small hammer or a screw driver and you can see that it runs smooth, now if the egr valve is vacum controlled replace the valve. if it is electronoc controlled replace the valve and the module for the egr valve.

Posted on Nov 24, 2008

  • 2 Answers

SOURCE: Horn on my car does not work..not safe!!!

if you have power at the connections, & all connections are good, try tapping the horn unit lightly with a hammer. In a garage I worked at some years ago we would remove the horn unit & drop it on the floor, if it didn't work after that it usually ment the internal coil was burnt out & the unit needed replacing. There should be a resistance reading across the terminals of the unit (when disconnected) although this will require a test meter.

Posted on Apr 26, 2009

  • 1 Answer

SOURCE: stuck hood on 2000 ford 250, latch release won't work

2000 FORD SUPER DUTY 5.4 HOOD STICKS.YOU CAN HAVE AN ASSISTANT PULL THE HOOD CABLE AND EASILY OPEN THE HOOD BUT THE HOOD WILL NOT POP UP ON ITS OWN..ANY ADVISE?

Posted on Nov 05, 2009

johnjohn2
  • 5763 Answers

SOURCE: broken hood release cable. Can't open hood

this is a hard one it depends on where it broke,can you cut the housing to get to cable core and pull with pleirs, if it snapped at latch then you will need to remove the grill or go from the bottom and try to hit the release the same wat the cable did,sometime if you grab the cable near the latch and pull hard it will open, good luck.

Posted on May 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i open a trunk to a 1996 Crown vic? I can't use a key and i can't open from inside because my battery is dead?


There should be a safety trunk release located on the upper rear window deck platform- a black handpull . If it is still intact- it should pop the trunk lid. At least it works that way on a 1997 Crown Vic.

Feb 12, 2016 | 1996 Ford Crown Victoria

1 Answer

Why my 2007 crown Vic won't shift in gear


this can be due to out of adjutment of shifter cable which releases the shifter when brake is pressed.

Nov 18, 2011 | 2007 Ford Crown Victoria LX Sedan

2 Answers

1992 CROWN VICTORIA LX I REPLACED FUSES INSIDE AND UNDER HOOD FOR AIR RIDE SUSPENSION AND IT STILL WON'T AIR UP. PLEASE HELP


Air ride suspension basically works like this. you have a small air compressor and a sensor that connects between the rear axle and the under body Frame. When this sensor detects a load movement like more or less weight it turns on the air compressor to air up or opens a exhaust valve to let air out. most common problems with this system. broken or disconnected sensor. leak in the air lines between compressor and shocks. or a bad or weak compressor.

Feb 08, 2011 | 1992 Ford Crown Victoria

3 Answers

On my 2000 ford crown vic. the power door locks work except for the drivers side. sounds like something is rattleing in the door. any ideas on what and how to fix


the power lock in that door may have broke the rod. remove the door panel to inspect its operation and replace the necessary part. hope this helps

Jan 31, 2011 | 2000 Ford Crown Victoria

1 Answer

2000 crown vic police interceptor bypass a/c clutch pulley


you can get a A/C Delete kit for a Ford 4.6 liter. the 4.6 v-8 accessory drive system is all the same. You may also be able to run a line of string around the pullys, take it to your local auto parts store and they can match it up. I recomend the kit,

Oct 05, 2009 | 2000 Ford Crown Victoria

1 Answer

When I turn on the heat/AC on my 2000 crown vic my turning signal fuse blows. What could be the problem?


My heat nor turn signals work worked fine then stopped. I have a 91 lx crown Victoria

Sep 23, 2009 | 2000 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...