Question about 2004 Ford Explorer

Open Question

Location of battery saver relay

No gauges windows or interior lights

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7353 Answers

SOURCE: trying to find the actual, exact location of the

I dont think a 2001 Taurus has a Battery Discharge Protection Relay.

Posted on Sep 12, 2011

Dragonzride
  • 9 Answers

SOURCE: 96 taurus wagon interior lights and power windows

just a guess but Id look for a bad chasis ground. I say this cuz the interior light switch for the door is a normally- open - grounding. The test for this theory would be to run a jumper wire from the neg batt terminal to the body, or from the eng to the body/chasis.

Posted on Jan 03, 2009

  • 1 Answer

SOURCE: battery saver relay is on and wont start taurus 1999

where is the battery relay saver on ford ranger 98 4x4

Posted on May 01, 2010

jturcotte
  • 7772 Answers

SOURCE: I have no power to

Hi, that relay should be in the box under the dash as shown below

jturcotte_2111.gif

jturcotte_2112.gif

Posted on Aug 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the interior light relay on 2001 ford windstar


Your interior lights are controlled by the GEM - generic electronic module !
Battery Saver The battery saver relay is controlled by the generic electronic module (GEM) and is located in the fuse junction panel. The battery saver relay is designed to supply B+ voltage to the following:
  • dome and map lamp switches
  • visor lamps
  • glove box lamp switch
  • interior lamp switch
  • interior courtesy lamp relay
  • delayed accessory relay
The function of the battery saver relay is to prevent excessive battery drain by interior lighting circuits. The GEM supplies a ground signal to the battery saver relay anytime one of the wake-up inputs of the GEM is activated to operate the battery saver relay. A wake-up command is sent when:
  • any door becomes ajar or is opened or closed.
  • the ignition key is inserted or removed.
  • the ignition switch is turned from OFF to RUN.
  • the ignition switch is turned from OFF to ACC.
  • a wake-up request is received from the remote anti-theft personality (RAP) module (if equipped).
  • The GEM will maintain the ground input with ignition in RUN or for 40 minutes from the last input activation with ignition in the OFF position. After 40 minutes the ground signal is discontinued.
This de-engergizes the battery saver relay preventing B+ voltage supply to the controlled switches and circuits.
  • Courtesy Lamp On Continuously
  • Short to power.
  • Damaged switch.
  • Generic electronic module.
  • GO to Pinpoint Test AF .
PINPOINT TEST AF: COURTESY LAMPS ON CONTINUOUSLY AF1 PRELIMINARY CHECKS
  • Check connections for clean tight fit.
  • Check for loose or damaged wires.
Do components and wiring check OK? Yes No GO to AF2 . SERVICE or REPLACE as required. GO to AF2 . AF2 CHECK CIRCUIT 53 (BK/LB)
  • Remove interior lamp relay.
  • Measure voltage at interior lamp relay connector Pin 87, Circuit 53 (BK/LB).
Is voltage greater than 0 volts? Yes No SERVICE Circuit 53 (BK/LB) for short to B+. RESTORE vehicle. RETEST system. GO to AF3 . AF3 CHECK CIRCUIT 434 (LB/BK)
  • Measure resistance between interior lamp relay connector Pin 85, Circuit 434 (LB/BK) and ground.
Is resistance 5 ohms or less? Yes No SERVICE Circuit 434 (LB/BK) for short to ground. RESTORE vehicle. RETEST system. REPLACE interior lamp relay. RESTORE vehicle. RETEST system. Interior lamp relay is located in the Instrument panel fuse box .
I/P Fuse Panel (Located Below Driver's Side of I/P )

Feb 28, 2015 | 2001 Ford Windstar

1 Answer

1999 silverado gauge lights do not work


You probably already checked this but the simplest solution is the control used to turn on the interior lights and to dim your dash lights. It is a dimmer switch to the right of your headlight switch. If it is turned all the way down then you would have no dash lights and no headlight chime. Turned all the way up it turns on your interior lights. If this isn't your issue and if no fuses are blown then try to turn the dimmer switch all the way up with your headlights on. If the dash lights come on with the interior lights then your switch is fried and you may have a short in the interior light circuit.

Jan 13, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

Dash lights and all interior lights dont work 98 accord


It is likely the interior lighting dimmer control switch is defective or turned off.

Feb 09, 2012 | Cars & Trucks

1 Answer

2000 FORD EXPLOYER: Power windows, dome lights not working which fuse number controls it?


Hello! In the Central Junction Box is fuse # 26 (10A) which powers the Battery Saver Relay...This relay, in-turn, controls the Power Windows, Electronic Shift Module, Glove compartment Light and Cargo light...If the fuse is good, suspect the relay...The Interior Lamp Relay and the Battery Saver Relay are the same...Either one could be at fault if the fuse proves to be good...See photo of relay below...Relay module Above right of gas pedal or lower left of AC/Heater/radio. It is an ugly place (Behind the center console)...

This is a documented fault if fuse #26 keeps blowing...The wiring on the rear of the relay module has a history of shorted and burnt connections on the socket of the Battery Saver Relay...Keep me posted...................Guru............Saailer



saailer_165.jpgSTANDARD MOTOR PRODUCTS Part # RY612...Cost under $10

Aug 30, 2011 | Ford Explorer Cars & Trucks

1 Answer

My 4WD dash lights are flashing and the 4WD won't engage. Also, my power windows and moonroof won't work. I've checked all of the fuses and they're good. What else should I check?


There's a TSB out for this concern. Its just a faulty relay

adobe.gif Printable View (8 KB) TSB
98-13-19
  • ELECTRICAL - LOSS OF 4X4 SYSTEM
  • LAMP - 4X4 LAMP ILLUMINATED
  • LAMP - NO INTERIOR LIGHTING
  • MOON ROOF - INTERMITTENT OR LOSS OF POWER
  • REAR WIPER - INTERMITTENT OR LOSS OF POWER
  • WINDOWS - INTERMITTENT OR LOSS OF POWER
Publication Date: JULY 6, 1998
LIGHT TRUCK: 1997-1998 EXPLORER, MOUNTAINEER
This TSB article is being republished in its entirety to correct the Service Procedure Steps. ISSUE: A flashing 4X4 lamp and/or a intermittent or loss of:
  • Power windows
  • Interior lights
  • Rear wiper (if equipped)
  • Moon roof (if equipped)
  • 4x4 system (if equipped)
may occur on some vehicles. This may be caused by an intermittent Battery Saver, Accessory Delay or One-Touch-Down Relay operation and possible chafing of vehicle wire harness.
ACTION: Repair the affected circuit, and/or replace the Battery Saver, Accessory Delay, or One-Touch-Down Relay. Refer to the following Diagnostic/Service Procedure for details before replacing any components.
DIAGNOSTIC/SERVICE PROCEDURE Accurately RECORD ALL Diagnostic Trouble Codes (DTCs) from the Generic Electronic Module (GEM). The following codes can be generated by a faulty relay:
  • B1371-Illuminated Entry Relay-Circuit
  • B1302-Accessory Delay Relay-Circuit
  • B1398-One-Touch-Down Relay-Circuit 1
  • B1814-Rear Wiper Motor Down Relay-Circuit
  • B1818-Rear Wiper Motor Up Relay-Circuit
  • P1820-Transfer Case L2H Relay-Circuit
  • P1824-Clutch Relay-Circuit
  • P1828-Transfer Case H2L Relay-Circuit
DIAGNOSIS
  1. If you have any of these codes B1371, B1814, B1818, and/or the interior lights or rear wipers are part of the customer concerns, go to Step 12. Otherwise locate the Accesory Delay Relay and proceed to next Step.
  2. Put key in "RUN."
    1. If conditions are repeatable, go to Step 3.
    2. If conditions are not repeatable, follow standard GEM troubleshooting procedures.
  3. Operate the windows until they fail then proceed to next Step.
  4. Remove relay from relay box then proceed to next Step.
  5. Check for battery voltage at Pin 87.
    1. If battery voltage is present, go to Step 6.
    2. If battery voltage is not present, go to Step 23.
  6. Check for battery voltage at Pin 86.
    1. If battery voltage is present, go to Step 8.
    2. If battery voltage is not present, go to Step 7.
  7. Locate the Battery Saver Relay and check Pin 3 for battery voltage.
    1. If battery voltage is present, go to Step 23.
    2. If battery voltage is not present, go to Step 16.
  8. Return the Accessory Delay Relay back to the relay box then proceed to next Step.
  9. Check for Ground at Pin 85.
    1. If Ground is present, go to Step 10.
    2. If Ground is not present, follow standard GEM troubleshooting procedures.
  10. Check for battery voltage at Pin 30.
    1. If battery voltage is present, follow normal GEM diagnostic procedures.
    2. If battery voltage is not present, go to Step 11.
  11. Check all female terminals at the relay.
    1. If all terminals are tight and all wiring crimps are good, REPLACE the Accessory Delay Relay, then go to Step 22.
    2. Make sure all terminals are tight and all wiring crimps are secure then go to Step 9.
  12. Locate the Battery Saver Relay.
  13. Put key in "RUN."
    1. If conditions are repeatable, go to Step 14.
    2. If conditions are not repeatable, follow standard GEM troubleshooting procedures.
  14. Operate the windows until they fail then proceed to next Step.
  15. Remove relay from relay box then proceed to next Step.
  16. Check for battery voltage at Pin 1.
    1. If battery voltage is present, go to Step 17.
    2. If battery voltage is not present, go to Step 23.
  17. Check for battery voltage at Pin 5.
    1. If battery voltage is present, go to Step 18.
    2. If battery voltage is not present, go to Step 23.
  18. Return the Battery Saver Relay back to the relay box then proceed to next Step.
  19. Check for Ground at Pin 2.
    1. If Ground is present, go to Step 20.
    2. If Ground is not present, follow standard GEM troubleshooting procedures.
  20. Check for battery voltage at Pin 3.
    1. If battery voltage is present, follow standard GEM troubleshooting procedures.
    2. If battery voltage is not present, go to Step 21.
  21. Check all female terminals at the relay.
    1. If all terminals are tight and all wiring crimps are good, REPLACE the Battery Saver Relay, then go to Step 22.
    2. Make sure all terminals are tight and all wiring crimps are secure then go to Step 19.
  22. Verify all concerns are corrected.
    1. If all concerns are corrected, return vehicle to customer.
    2. If all concerns are NOT corrected, go to Step 23.
  23. This is Not a GEM-related issue. Follow standard troubleshooting procedures.

PART NUMBER PART NAME F5TZ-14N089-B Relay - One-Touch-Down And Battery Saver FOAZ-14N089-A Relay - Accessory Delay F77Z-14B205-AA Generic Electronic Module (GEM) (1997 4X2) F77Z-14B205-BC Generic Electronic Module (GEM) (1997 4X4) F87Z-14B205-BA Generic Electronic Module (GEM) (1998 4X2) F87Z-14B205-CB Generic Electronic Module (GEM) (1998 4X4)
OTHER APPLICABLE ARTICLES: NONE
SUPERSEDES: 98-11-6
WARRANTY STATUS: Eligible Under The Provisions Of Bumper To Bumper Warranty Coverage
OPERATION DESCRIPTION TIME 981319A Perform Pinpoint Tests 1.0 Hr. 981319B Replace Relay 0.2 Hr.
DEALER CODING BASIC PART NO. CONDITION CODE 14B205, 14N089 42
OASIS CODES: 102000, 105000, 201100, 202000, 203200, 206000, 502000, 504000, 508000

Copyright © 1998 Ford Motor Company
2010&c18=modelyear&c21=98-13-19&c35=tsb%2c98-13-19&s=1366x768&c=32&j=1.3&v=y&k=y&bw=1329&bh=453&ct=lan&hp=n&[aqe]

Mar 10, 2011 | 1998 Ford Explorer

1 Answer

Ok, today I replaced/removed several exterior lights: 1) I replaced the left headlight 2) I removed a burned out bulb from the high mount brakelight (local part store was out of stock, coming in...


I can help you out with the left turn signal not blinking. Maybe it's a flasher or the light bulbs aren't getting current through the wiring.

I can't help you out with the interior gauge lights not turning on when you turn the headlamps on. It may have to do with the headlamp switch, though.

I've never seen the lights on the radio not dim when the headlamp switch is turned on. hm.

Good luck on this repair.

Nov 03, 2010 | 1990 Pontiac Firebird

1 Answer

2004 chev avalanch would start then quit. Battery was low. Altenator was faulty. Replaced. Now all interior components won't work. Power windows, gauges, interiour lights ect. Truck will run. Dealer...


sounds like bad fusible link or u forgot to hook up wire somewhere (i think dealear wrong wouldnt start if problem was anti theft) (after all if your stealing a car would u care if interior componets worked probley not)

Jun 12, 2010 | 2004 Chevrolet Avalanche

1 Answer

2003 fairlady 350z fuse


Fuse Box should be located under the dash just beside the driver's door. It sounds like you may have a bigger issue than just a blown fuse. The interior lights are on one fuse, the instrument gauge is on another fuse, the rear window is on another fuse. For all three to blow, it would seem that there's an electrical short somewhere.

Aug 04, 2009 | 2004 Nissan 350Z

2 Answers

Fuse box diagram for 2002 ford taurus


The 1999 Fuse Box Diagram is as follows:

Column 1 (Top to Bottom)
Driver Window Relay
Interior Lamp Relay
Driver Unlock Relay
Battery Saver Relay
Hazard Lamps (15A)
Diagnos (10A)
Cigar (20A)
Front Wipers (30A)
Air Bag (5A)
ABS (10A)
Shift Interlock (5A)
Blank

Column 2 (Top to Bottom)
High Beams (15A)
Deck Lid Release (15A)
Mirrors/Antenna (5A)
Head Lamp Illumenation (5A)
Light Out Module (5A)
EEC Ignition Coil (20A)
Brake Lamps/ A/C (15A)
Instrument Illumenation (5A)

Column 3 (Top to Bottom)
Accessorty Delay Relay
Rear Defrost Relay
Tail Lamps (5A)
Battery Saver (10A)
Wiper and Vaps (5A)
Rear Wiper (15A)
Turn Signal (10A)
Air bag/ Alt LPS (A)
Starter Relay (10A)
Left Low Beams (10A)

Column 4 (Top to Bottom)
Switch Illumenation (5A)
Def Sw Illumenation (10A)
Stop Lamps (15A)
Radio (5A)
Radio Memory (5A)
Right Hand Power Locks (20A)
Gauges/ Warning Lamps (5A)
Radio Mute (5A)
Right Low Beam (10A)

Hope this helps.

Apr 19, 2009 | 2002 Ford Taurus

Not finding what you are looking for?
2004 Ford Explorer Logo

Related Topics:

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...