Question about 2006 Ford Expedition

Open Question

How do I remove the governor on a 06 Ford expedition?

Posted by on

  • yadayada
    yadayada Feb 13, 2012

    Governor for what?

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of cabin air filter on 2004 ford expedition 5.4l


Doesn't have one .
SECTION 412-01: Air Distribution and Filtering 2004 Expedition/Navigator Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/23/2003 Air Distribution NOTE: The air distribution system of this vehicle cannot be equipped with a cabin air filter

Jun 12, 2017 | Ford Cars & Trucks

1 Answer

I HAVE A 2005 FORD EXPEDITION THE PROBLEM IS A CODE P0420


http://www.ford-trucks.com/forums/1011390-06-expedition-xlt-p0420-code.html

Mar 17, 2015 | 2005 Ford Expedition XLT

1 Answer

Where is the fuel pressure regulator located in my 06 ford expedition limited?


vehicle does not contain a fuel pressure regulator, it is controlled by the pcm and fuel pump driver module, there is a fuel pressure and temp. sensor located on the driver side of the fuel rail.

Nov 02, 2013 | 2006 Ford Expedition

1 Answer

06 expedition speedometer does not work


speed sensor or the inst. cluster

Jun 13, 2012 | 2003 Ford Expedition

1 Answer

How to remove rear wheel bearings on my 1999 Ford Expedition and how do i know what pulley to rent/buy?


The 1999 Ford Expedition is built on an F150 platform. The Expedition uses a 9.75-inch rear axle. The axles are retained with C-clips at the end of the axle shaft, inside the differential carrier. The axle bearings are of the roller type. A failed axle bearing can manifest itself as a noise at the rear wheel or gear oil leaking past the oil seal. When replacing axle bearings, the oil seals must also be replaced.
Torque the caliper mounting bolts to 30 foot-pounds. Torque the bolt to 20 foot-pounds with a torque wrench and socket. Click this link below for complete detailed procedure:--- http://technoanswers.blogspot.com/2011/06/how-to-remove-rear-wheel-bearings-on.html -------------- This should help.Thanks.Helpmech.

Jun 07, 2011 | Ford Expedition Cars & Trucks

1 Answer

How to replace the starter on a 03 Ford Expedition?


SECTION 303-06: Starting System 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/06/2002 Starter Motor adobe.gif Printable View (188 KB) Removal
ani_caut.gif WARNING: When carrying out maintenance on the starting system be aware that heavy gauge leads are connected directly to the battery. Make sure protective caps are in place when maintenance is complete. Failure to follow these instructions may result in personal injury.
  1. Disconnect the battery ground cable.
  1. ani_caut.gif WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the RH kick panel area. Failure to do so may result in unexpected inflation or deflation of the air springs which may result in shifting of the vehicle during these operations.
    Raise and support the vehicle; refer to Section 100-02.
  1. Remove the starter motor solenoid terminal cover.
    a0044571.gif
  1. Disconnect the starter motor electrical connections.
    a0044572.gif
  1. Remove the starter motor.
    1. Remove the stud bolts.
    1. Remove the two bolts.
    1. Remove the starter.
    a0044573.gif
Installation
ani_caut.gif WARNING: When carrying out maintenance on the starting system be aware that heavy gauge leads are connected directly to the battery. Make sure protective caps are in place when maintenance is complete. Failure to follow these instructions may result in personal injury.
  1. Install the starter motor.
    1. Position the starter.
    1. Install the two bolts.
    1. Install the stud bolt.
    a0044581.gif
  1. Connect the starter motor electrical connections.
    a0044582.gif
  1. Install the starter motor solenoid terminal cover.
    a0044571.gif
  1. Lower the vehicle.
  1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
    Connect the battery ground cable.

Mar 08, 2011 | 2003 Ford Expedition

1 Answer

06 ford expedition. a/c just stopped blowing. i don't even hear compressor cycling. is this a low refrigerant issue or something else?


I would check the refrigerant level. Also check the fuses. Also check to see if turning on the defrost turns on the A/C compressor.

May 07, 2010 | 2006 Ford Expedition

1 Answer

How would i go about disassembling the body of my 06 expedition after a crash is there a diagram or a computer program?


get a bolster chisel and a disk cutter and strip it ,by cutting it apart ,its all welded together

Jan 18, 2010 | 2006 Ford Expedition

1 Answer

06 Expedition Engine fail safe mode


truck needs to be scanned for the codes,most major parts stores will do this for little or no charge,get back to me with the codes and we'll go from there

May 15, 2009 | 2006 Ford Expedition

Not finding what you are looking for?
2006 Ford Expedition Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...