Question about 2006 Mitsubishi Colt

Open Question

Change front pads on colt cz2 - 2006 Mitsubishi Colt

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 347 Answers

SOURCE: REPLACE HEATER DIAL BULB ON 06 CZ2 COLT

there are screws at the side of the console. they are covered with round plastic plugs

Posted on Aug 29, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I release frozen front brake caliber on 79 dodge colt ?


Open the bleeder on the caliper, then using a large C clamp, clamp it onto the back of the caliper and the middle of the front pad. Tighten it to force the caliper piston back into the housing. If its really stuck you may need to use a bar on the C lamp handle to give you more leverage to get it moving. If the guides are really rusted try soaking with WD40 to free them up before applying pressure..

Mar 06, 2015 | Dodge Colt Cars & Trucks

1 Answer

Mitsubishi Colt CZ2. Fault code C1278 (valve relay stuck off). where is relay located?


Have you looked in the owner's manual for the location? It must be in the underhood fuse and relay center.

Oct 09, 2014 | 2006 Mitsubishi Colt

2 Answers

I have a 91 plymouth colt, changing the brakes and the pads i got will not fit. it is a 91 hatchback with the 1.5, its a 4 speed and not awd. I have went to multiple auto stores and they always give me the...


I'm including a link to RockAuto listing for brake pads for 1991 Plymouth Colt. Look down in the 'economy' (orange) section, and you will see a lot of listings. Many have -535 part number, but some have -299 and -602. These state they're for Colts built in Japan. Check inside the driver's door and see where your car was built. There's also references to LA model and GL model, so see if yours is one of these.
1991 PLYMOUTH COLT 1 5L L4 Brake Pad RockAuto

Sep 09, 2017 | 1991 Plymouth Colt

1 Answer

How to remove brake pads on a mistubishi colt bakkie


Jack & support with stands, remove wheels, undo botom caliperslide bolt, flip up calliper & remove pads only 1 side, drain some fluid out of the brake master cylinder, push caliper piston back with G clamp, install new pads, flip caliper down & do up bottom bolt, repeat with other side, replace wheels & your done

Jun 22, 2012 | Mitsubishi Cars & Trucks

1 Answer

Mitsubishi colt brake pads


If you watch the video at this YouTube LINK you will get the info you need to do the job, it is a differnet model but the procedure is the same.

Jun 22, 2012 | Cars & Trucks

2 Answers

My Mitsubishi colt CZ1 (07 plate) has problem with cental locking. I can manually central lock but with the remote it locks/unlocks all the doors except the driver's door. Please help. Thanks


Central locking works by way of little electric motors that engages and disengages the door lock. The drivers door has an additional set of contacts in the actuator which signal the controller when it changes position. The controller activates the servo motors when a signal is received from the receiver or from the drivers door servo motor. So in your case I suspect the motor part of the drivers door actuator is done for.
To replace you will have to remove the inner driver's door panel to get at the actuator. The actuator itself cannot be repaired and needs to be replaced as a unit.

Apr 29, 2011 | 2006 Mitsubishi Colt

1 Answer

Instal front brake pads


Check out this site, they have a lot of instructional video's. just search for brake pad replacement.
www.youtube.com

Dec 09, 2009 | 2006 Mitsubishi Colt

1 Answer

REPLACE HEATER DIAL BULB ON 06 CZ2 COLT


there are screws at the side of the console. they are covered with round plastic plugs

Aug 29, 2009 | Mitsubishi Colt Cars & Trucks

Not finding what you are looking for?
2006 Mitsubishi Colt Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...