Question about 1994 Ford Explorer Limited

Open Question

Diagram of front hub and axle 1994 Ford explorer 4 wheel drive.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 ford ranger 4x4 hubs make grinding/clicking noise after taken out of four wheel drive


I think yours has the automatic locking hubs that slide over the the rotor hub. If this is the case than what has probably happened is a u-joint has gone bad and wiped out that auto hub.

Be prepared for some sticker shock on those hubs. they are not cheap. The usual fix for this is to replace the front axle ujoints and what ever hub is making the noise, hopefully just one.

Feb 14, 2012 | 1994 Ford Ranger Supercab

1 Answer

How to replace wheel bearing on 1996 ford explorer


Is it a 2 wheel drive of 4 wheel drive explorer?? I'm going to take a shot in the dark and go with 4x4. Remove the cotter pin and axle nut. Then jack up and brace the vehicle. Remove the front tire (since you said wheel bearing and not axle bearing), caliper, caliper bracket, and the three bolts on the back of the spindle that hold in the bearing and hub. Slide the hub and bearing out. May take a couple of taps with a hammer.

Nov 26, 2010 | 1996 Ford Explorer

1 Answer

How to engage 4x4 in a 94 ford exploer (auto trans) mauale hubs


Before you start the vehicle lock the hubs in by turning the lock out device in the hub center of each front hub. Now you can start the vehicle and while in park or neutral move the range selector on the floor to the range you would like to use. Most often you will use the 4 wheel high setting. The low setting is only for extremely heavy pulling and will throw you across the seat if you accelerate too hard. Never exceed 45 miles per hour when in 4 wheel drive as you will burn out the transmission or 4X4 transfercase bearings. Now to go back to two wheel drive. Move the floor selecter back to 2 wheel drive setting. Do this with the vehicle in park or neutral to prevent damage to the vehicle. Now you can unlock the hubs by reversing the hub lock out device in the center of the two front hubs. Important little known fact is that you do not want to drive aroind with the hubs constantly locked in as you will lower your fuel mileage and cause extra wear to the axles and associated parts. Hope that helps, please come see us again if you have any more questions, Thanks, Rich.

Nov 21, 2010 | 1994 Ford Explorer Limited

1 Answer

I am looking for an exploded view of the front part of the 4 wheel drive system


there are 2, here's one.

Dana 44-IFS Front Drive Axle, Bronco and F-150 4x4 with Automatic Hub Locks


snorkelbobby_5.gif

Nov 09, 2010 | 1994 Ford F250 Supercab

1 Answer

1994 pontiac sunfire... the rear axle shaft is making noise in reverse. Is this safe to drive and how much to get repaired. by service station or at home


you should first check your hub assembly or wheel bearings if is a sunfire because i dont remember had worked on asunfire with 4 wheel drive or rear wheel drive they are front wheel drive and the axle shafts are in the front

Nov 07, 2009 | 1994 Pontiac Sunbird

1 Answer

No power to hubs


Lary,
A possible problem is the cv axle. cv axles ar eknown for going out on those Explorers. Check them and contact me for further assintance.

Jan 30, 2009 | 1998 Ford Explorer

2 Answers

1994 ford explorer 4 wheel drive not working


I miss spoke...What had happen was that my front end was turning but hubs were not engaging...finally figured out automatic hubs were bad... when my ex had it she had a bearing repacking done, but they also put grease in hub.. wore down parts.. hope that helps..

Nov 05, 2008 | 1994 Ford Explorer Limited

1 Answer

1994 ford explorer 4 wheel drive not working


Go to the engine compartment where the relays are located with the fuses. Check or replace the 4 wheel auto engage relay , maybe is not working. Is very clearly mark, I believe is the top right one looking at the bost front front of vehicle to the back. There is a diagram drawing of each relay in the cover, so you can't go wrong.

Oct 26, 2008 | 1994 Ford Explorer Limited

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

18,296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...