Question about 1995 Ford Windstar

1 Answer

How to bleed cooling system on 1995 windstar with 3.8

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,797 Answers

Use a floor jack and raise the car up as high as possible, fill the coolant recovery tank as full as possible and run the engine until it reaches the high end of normal temperature, shut it down and run cols water war over the radiator, the air will self bleed and coolant will be pulled into the radiator as it cools to fill the void. The radiator cap is left on during this procedure.

Posted on Feb 13, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding the coolant system 2005 chevy uplander


Bleeding the coolant system Leisa, Check the attached links,instruction and guides on bleeding cooling systems. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Fill Bleed Coolant Chevy 3 4L V6
Bleeding Air In Cooling System
Coolant Flush How to Chevrolet Uplander 2005 2008 2008 Chevrolet Uplander...
How To Bleed Cooling System EricTheCarGuy


May 21, 2016 | Cars & Trucks

Tip

Cooling system


Flush and bleed the cooling system every two years. Use BMW coolant and distilled water 50/50 mix.

on May 19, 2008 | 1995 BMW 3 Series

1 Answer

Overheats could this be from to much coolent rushed the radiator and refilled just Wonder if added to much coolent


If you have emptied the cooling system and refilled it, you need to bleed air out of the system using the correct procedure for your engine.
If you did not bleed air out after refilling, you will have air trapped in the cooling system and it will not function properly. You will most likely get an overheating condition.

Dec 19, 2015 | 2003 Ford Windstar

1 Answer

Cooling system needs bleeding xedos 6 v6.20 where is bleed nipple


There is no bleed nipple in a cooling system. You'll need a vacuum pump and the proper adapter for the radiator.

May 10, 2011 | 1995 Mazda MX-3

1 Answer

Added colant and the car is now overheating


That's because you need to bleed the cooling system, now. Here is a link to an article that will tell you how to bleed the cooling system on your car.

Dec 24, 2010 | 1995 Oldsmobile Aurora

1 Answer

How do you bleed cooling system for 1995 nissan pickup truck


  1. Open radiator cap and air relief plug.
  2. Fill radiator with coolant to specified level.
  3. Close air relief plug.
  4. Run engine and bring to operating temperature.
  5. Race engine two or three times under no-load.
  6. Stop engine and let cool, then add coolant as necessary.

May 10, 2010 | 1995 Nissan Pickup

1 Answer

Heater on 1995 Chrysler Concorde stopped heating. Replaced water pump and thermostat. Blows semi warm air out of one dash vent and pure cold out of other dash vent. Does anyone know codes to reset?


there are no reset codes, did you bleed the air out of the cooling system? if not do this procedure, if that doeasn't fix it u have a failed air temperasture control blend door motor actuator.
The generic method of bleeding air from the cooling system is to use a floor jack and raise the front of the car as high as poss, then fill the coolant recovery tank full and run the engine until it just starts to overheat, high end of normal zone on gauge, then shut the engine down and run cold water over the radiator core, this will self bleed the system and the coolant will be pulled from the recovery tank, repeat as necessary, never let the recovery tank run dry or more air will be pulled into the cooling systeml ,

Jan 11, 2010 | 1995 Chrysler Concorde

1 Answer

I need to bleed air from my radiator/engine block cooling system after installing a new water pump and other items.How do I locate the vent port or bleed valve on the block or wherever?Where is it located?


It is usually located on either the thermostat housing or on the highest point in the cooling system top radiator hose housing going into the engine. Run the motor for approx. ten minutes then turn heater on high unscrew bleeder 3/4 of a turn and then turn back in when coolant squirts out. Repeat after 5 more minutes of run time.

Jan 05, 2010 | 1995 Ford F150 Styleside Regular Cab

1 Answer

1995 Ford Windstar wont start win the cooling fans are on


If cooling fans are running then the PCM is not powering up. Check or replace the PCM relay in the under hood fuse panel

May 12, 2009 | 1995 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...