Question about 2001 Chevrolet Silverado 1500

Open Question

How to replace knock sensor on 2001 Nissan Frontier 4 cylinder

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 636 Answers

SOURCE: knock sensor

check out you tube, replacing knock sensor

Posted on Sep 05, 2009

Ad
  • 1 Answer

SOURCE: Steps to replace a knock Sensors?

I had to do this last summer. First I went to Advanced Auto. They
read the code for me. One of them was bad, but I went ahead and
replaced both. I purchased a manual for the steps, two knock sensors
and a gasket set. About 170 dollars total. You will also need a torq
wrench in inch pounds. Take your time, keep it clean. Make sure
you clean the manifold and engine head surfaces where the gasket
seats. Use a non metallic scraper, and if need be solvent to loosen
any old gasket material. I found that laying saturated rags on the
head surface and leaving them set a few hours helped the most.
You can also get the steps and torque specs from either Advance
auto or Auto Zone(then you don't need the manual).
Use patience when tightening the manifold bolts, you should
torque them in the sequence given(in the manual or online) and
you have to do it twice, first time at half torque, then the second at
full torque. If you over tighten you can crack the manifold.
Good luck
Art LeDoux, Stillman Valley Illinois

Posted on Dec 28, 2009

BCAS1298
  • 3092 Answers

SOURCE: replace knock sensor on 2001 chevy 4.8

You have two knock sensor's, both sit under the in-take magifold on top of the engine, you will have to remove injector rail and in-take.

Posted on Apr 13, 2010

  • 1 Answer

SOURCE: need how to and location to replace knock sensor

Im looking for the same part location on a 2002 chevy blazer. It might be under the distributer cap.

Posted on Nov 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where I can locate po325 knock sensor for nissan frontier 2000


underneath intake manifold between cylinder 1 and 2.

Mar 09, 2015 | 2000 Nissan Frontier

1 Answer

How do I bypass a knock sensor on a 2000 Nissan frontier


Bypassing (hotwiring) the knock sensor will remove a signal the computer needs to operate. Unexpected results for sure , possible damage to the computer may result. Replacing the knock sensor is the best way.

Oct 12, 2014 | 2000 Nissan Frontier

3 Answers

How do I bypass a knock sensor on a 2000 Nissan frontier


The pcm uses the knock sensor to monitor for engine knocking, and adjusts ignition timing based on this. If there is no knock sensor present, you will wind up with a hard fault that will keep the check engine lamp on continuously. Also, the truck will go into a more conservative driving mode to prevent knocking.
The knock sensor for a frontier is not terribly expensive, but it is a pain to access on nissan v6s, under the intake manifold

Oct 12, 2014 | 2000 Nissan Frontier

2 Answers

Replacing knock sensor do I need to replace the harrness


No you don't have to change the harness unless it is cracked, broken, or have burn marks.

Nov 10, 2010 | 2000 Nissan Frontier

1 Answer

How many quarts for a 2001 nissan crewcab frontier


Nissan owner's manual says for a 4 cylinder (3-3/4 qts) and for a 6 cylinder (3-1/2 qts).

Sep 10, 2010 | 2001 Nissan Frontier Crew Cab

1 Answer

2000 nissan frontier knock sensor code & distributor


no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Jun 14, 2010 | 2000 Nissan Frontier

1 Answer

Where is the knock sensor located on a 2003 nissan frontier 3.3 v/6 engine?


It is located on the engine block itself in the valley between the cylinder heads. The entire intake manifold has to come off to access it:

Oct 30, 2009 | 2003 Nissan Frontier Crew Cab

1 Answer

Location of knock sensor


Knock sensors can be difficult to locate because there usually buried under intake or exhaust manifolds and misc. engine wiring and plumbing. Knock sensors need to hear an engine knocking noise, therefore there usually located somewhere they can hear an engine knock. If it's a V6 then possibly it will be between the cylinder heads and access to them can only be attained by removing the intake manifold. I would suggest calling a Nissan Dealer parts person and ask them. Good luck.

Jun 16, 2009 | 2004 Nissan Frontier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...