Question about 1999 Toyota Camry

Open Question

99 camry auto-trans.Dash light for reverse stays on when shift to drive

The dash indicator light R for reverse stays on after placed into drive

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 42 Answers

SOURCE: 2000 toyota camry check engine

wires are pinched and shorting together near the left (drivers side) trunk hinge. brake light power is feeding back through the reverse light wiring. this will also turn on the check engine light with a neutral safety switch malfunction code as the computer also sees this voltage in the reverse light circuit. Find and repair the wiring, pull the EFI fuse in the panel under the hood to clear the code. Hope this helps

Posted on Dec 28, 2008

Ad
  • 1 Answer

SOURCE: 1994 camry reverse indicator ilght on when breaking

Common to see a broken wire in the wire harness that runs along the left rear trunk hinge. They can cause all sorts of problems after years of bending when the trunk is opened and closed. You will need to carefully cut the wire loom and inspect these wires. Sometimes the wires are broken INSIDE the insulation and cannot be seen without stripping the wires.

Posted on Dec 13, 2008

  • 1861 Answers

SOURCE: 1994 Camry Red dash warning light stuck on

This is most likely the security system light.

Posted on Mar 15, 2009

LEFTY64
  • 69 Answers

SOURCE: removal and installation of an auto trans in 2002 toyota camry

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the transaxle fluid.
  3. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Battery Air cleaner assembly Throttle cable from the throttle body Cruise control actuator cover and connector, if equipped Ground wire Starter Speed sensor connectors, direct clutch speed sensor, and the park/neutral position switch connector on the transaxle Solenoid connector on the transaxle Shift control cable Oil cooler hoses Front side transaxle mounting bolts Front engine mounting bolts Oil cooler line mounting bolts from the front frame Upper transaxle to engine mounting bolts

    0900c15280197a59.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tie the steering rack to the engine support fixture components, as shown-Avalon and Camry
    Front exhaust pipe Engine side covers and undercovers Both halfshafts Front side engine mounting nut Rear side engine mounting bolts (remove hole plugs) Left side transaxle mounting bolts Steering gear housing Front frame assembly Rear end plate mounting bolts Torque converter cover Torque converter retaining bolts Remaining transaxle mounting bolts Transaxle

Posted on Apr 09, 2009

dsacco86
  • 1077 Answers

SOURCE: 1780 code

P1780 Park/Neutral Position Switch Malfunction (Only For A/T)
This code is related to a malfunction with the park neutral position switch, it's located on the transmission.
It maybe easier to get a Chilton manual from the autoparts store to locate the sensor/switch. The book runs about $20.
Replacing the switch/sensor may resolve the reverse light problem also.

Posted on Apr 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 isuzu rodeo wont shift outta 2nd gear


auto trans no less.. it shifts no you.
so what trans is there?
so reverse works, 1 gear, then 2nd , but not 3rd.
some have a TCM that does the auto shifts.
and must be scanned to see why it wont shift.
levels ok, that be like first first. done not like engine, ever.
do it correctly.
The TCM may have flash codes, the FSM factory serv. man. covers this, as does mitchells.but it will ask you
what engine you have, and which trans is car 4wd?
first know your drive train then ask.

Nov 02, 2016 | 1994 Isuzu Rodeo

1 Answer

1996 camry slow acceleration


On a Camry that year it is quite possible that

- if an auto, your no 1 & 2 shift solenoid has failed, rendering the trans unable to find low gear. Any auto mech can test for this easily (cheaply), however there should then be a trouble code causing the O/D indicator to blink on the dash (if that lamp is OK)

- if a manual, your clutch is worn and has begun to slip. Park on a level, idle the engine, step firmly on the footbrake, place the trans in 3rd gear and let the clutch out slowly. The engine should immediately stall. If it is slow to do so, suspect the clutch.

Oct 10, 2014 | 1996 Toyota Camry

1 Answer

Reset reverse light indicator camry


Make sure the tail lights and brake lights are working including the one in the rear window, if any of these are out the dash warning light will stay on, any bulbs that look discolored should be replaced

Mar 16, 2014 | Toyota Camry Cars & Trucks

1 Answer

Gear position indicator modulator


I have a 1999 Sienna toyota but my flickering light when car on..

Jan 05, 2014 | 2002 Chevrolet Silverado 1500

1 Answer

99 bmw 528i dash indicator light,sprocket with ! in it and trans shifting and down shifting hard


That light is telling you to have transmission serviced. not sure if it is the fluid or sensors. that is what a scan tool is for.

Dec 11, 2012 | BMW 525 Cars & Trucks

1 Answer

1990 toyota camry wont go into gear or slips out


Could be a long list of things.
Its too late for a filter change. Doing that now would probably make matters worse.
The trans uses electric solenoids and a pump to apply pressure to the clutches. So either could be faulty given the age and mileage.
I'm not sure if the shifting problem is connected to the shift indicator lights problem.
You may need to take it to a trans shop to find out for sure. And they will not want to touch it with that many miles on it.
A regular mechanic might be able to do a pressure test on it to at least find out if it is the pump or not.

Dec 04, 2012 | 1990 Toyota Camry

1 Answer

My 2001 Dodge Caravan's transmission is stuck in reverse.


Things haven't changed much...look on top of the transmission in the engine compartment and look at the shifting linkage. Look for anything that could be interfering with the shifting. One linkage is the cable to the Shift Lever and Rod that goes down into the transmission. Remove the cable adjustment screw.
Move the shift lever rod towards the front of the Van into the Park Indent Position. Place the Driver's Position (Dash) Shift Lever into Park and then reconnect the Cable to the Shift Lever and tighten down the cable adjustment screw to 70 in-lbs.
Check operation's
Let me know if this helped, or if you have any additional information, questions of problems, Feel free to contact me at FixYa.com!

Jan 25, 2010 | 2001 Dodge Caravan

Not finding what you are looking for?
1999 Toyota Camry Logo

Related Topics:

687 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...