Question about Hyundai Elantra

Open Question

2000 HYUNDAI ELANTRA HEATER CORE INSTALLATION

INSTRUCTIONS TO REPLACE HEATER CORE

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 176 Answers

SOURCE: Need to remove heater core from 2000 Daewoo Nubira

  1. Disconnect the negative battery cable.
  2. Remove the instrument panel from the vehicle.
  3. Remove the heater/air distributor case from the vehicle.
  4. Disconnect the vacuum actuators from the vent/floor door and the defroster door.
  5. Remove the vacuum actuators from the heater/air distributor case.
  6. Remove the screws that secure the heater core cover to the heater/air distributor case assembly.
  7. Slowly separate the lower heater core cover from the rest of the assembly
  1. Remove the screw and the bracket clamp that secure the heater core lines to the case.
  2. Remove the spring clamp that secures the heater core body to the case.
  3. Remove the heater core from the case.
  1. Install the heater core into the case.
  2. Secure the heater core lines to the case with the retaining bracket clamp and the screw. Tighten the heater core retaining bracket screw .
  3. Install the heater core body with the retaining spring clamp.
  1. Install the heater core cover.
  2. Install and tighten the screws that secure the heater core cover to the heater/air distributor case assembly. Tighten the heater core cover screws
  3. Install the actuators for the vent/floor and the defroster doors.
  4. Install the heater/air distributor case.
  5. Install the instrument panel.
  6. Fill the cooling system
  7. Connect the negative battery cable.

Posted on Jun 18, 2009

Ad
  • 1596 Answers

SOURCE: need instruction on installing heater core for 2000 jeep cherokee



The heater-A/C housing assembly must be removed from the vehicle and the two halves of the housing separated for service access of the heater core, evaporator coil, blend-air door, and each of the various mode control doors.

WARNING: On vehicles equipped with airbags, refer to Airbag Systems Safety Information and Procedures. Before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury. See: Restraint Systems\Air Bag Systems\Service Precautions

REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove the instrument panel from the vehicle. Refer to: Body and Frame, Interior Trim, Dashboard / Instrument Panel, Service and Repair, Instrument Panel Service Procedures, Instrument Panel Assembly Replacement, See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  3. If the vehicle is not equipped with air conditioning, go to Step 6. If the vehicle is equipped with air conditioning, recover the refrigerant from the refrigerant system. Refer to: Heating and Air Conditioning, Service and Repair, Procedures, Refrigerant System Recovery, See: Service and Repair\Refrigerant System Recovery
  4. Disconnect the liquid line refrigerant line fitting from the evaporator inlet tube.
    • Install plugs in, or tape over all of the opened refrigerant line fittings.
  1. Disconnect the accumulator inlet tube refrigerant line fitting from the evaporator outlet tube. See Refrigerant Line Coupler for the procedures.
    • Install plugs in, or tape over all of the opened refrigerant line fittings.
  1. Drain the engine cooling system.
  2. Disconnect the heater hoses from the heater core tubes. Install plugs in, or tape over the opened heater core tubes.
  3. Unplug the heater-A/C system vacuum supply line connector from the tee fitting near the heater core tubes.
  4. Unplug the heater-A/C unit wire harness connector, which is fastened to the heater-A/C housing next to the blower motor relay.
    1. Remove the five nuts from the heater-A/C housing mounting studs on the engine compartment side of the dash panel. Remove or reposition the evaporation canister for additional access, if required.
    2. Pull the heater-A/C housing rearward far enough for the mounting studs and the evaporator condensate drain tube to clear the dash panel holes.
    3. Remove the heater-A/C housing from the vehicle.
    INSTALLATION
    1. Position the heater-A/C housing to the dash panel. Be certain that the evaporator condensate drain tube and the housing mounting studs are inserted into their correct mounting holes.
    2. Install and tighten the five nuts onto the heater-A/C housing mounting studs on the engine compartment side of the dash panel. Tighten the nuts to 6.2 Nm (55 in. lbs.) .
    3. If the evaporation canister was repositioned during the removal procedure, reinstall it to its proper position.
    4. Connect the Heater-A/C system vacuum supply line connector to the tee fitting near the heater core tubes.
    5. Unplug or remove the tape from the heater core tubes. Connect the heater hoses to the heater core tubes and fill the engine cooling system.
    6. If the vehicle is not equipped with air conditioning, go to Step 10. If the vehicle is equipped with air conditioning, unplug or remove the tape from the accumulator inlet tube and the evaporator outlet tube fittings. Connect the accumulator inlet tube coupler to the evaporator outlet tube.
    7. Unplug or remove the tape from the liquid line and the evaporator inlet tube fittings. Connect the liquid line coupler to the evaporator inlet tube.
    8. Evacuate the refrigerant system. Refer to: Heating and Air Conditioning, Service and Repair, Procedures, Refrigerant System Evacuate, See: Service and Repair\Refrigerant System Evacuate
    9. Charge the refrigerant system. Refer to: Heating and Air Conditioning, Service and Repair, Procedures, Refrigerant System Charge, See: Service and Repair\Refrigerant System Charge
    10. Install the instrument panel in the vehicle. Refer to: Body and Frame, Interior Trim, Dashboard / Instrument Panel, Service and Repair, Instrument Panel Service Procedures, Instrument Panel Assembly Replacement, See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
    11. Connect the battery negative cable.
    12. Start the engine and check for proper operation of the heating and air conditioning systems.
REMOVAL AND INSTALLATION

WARNING: On vehicles equipped with airbags, refer to Airbag Systems Safety Information and Procedures. Before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury. See: Restraint Systems\Air Bag Systems\Service Precautions

  1. Remove and disassemble the heater-A/C housing. Refer to: Heating and Air Conditioning, Housing Assembly HVAC, Service and Repair, See: Heating and Air Conditioning\Housing Assembly HVAC\Service and Repair
  2. Lift the heater core out of the lower half of the heater-A/C housing.
  3. Reverse the removal procedures to install. Be certain that the heater core foam insulator is reinstalled

Posted on Feb 07, 2009

  • 80 Answers

SOURCE: need power window diagram for 2000 hyundai elantra

is this what your looking for??
Front Door Glass:
36c72f3.jpg

Posted on Apr 25, 2009

dnewcombe1
  • 1564 Answers

SOURCE: Replacing heater core in 2000 GMC sonoma. Dash is

If the dash is removed you've saved about 9 10ths of the job endurance. Look around, what you believe to be, the perimeter of the heater box. I cannot, and no one else can, tell you exactly where the bolts and nuts that mount the heater box are. Therefore you must viually sixe the box and check outide in the engine compartment and inside under the dash for the mounting bolts.You'll want to start by removing the heater hoses. Then starting at the passenger side engine compartment look for a group of 10mm or 7/16ths nuts retaining the housing and remove them. Do the same inside. The housing is usually held together with screws or clips, it changes year to year. Keep a log or pix of the wires and cables and hoses(vacuum) that are connected to the housing for reassembly. You'll need to "roll" the box out from under the dash depending on how much of the dash has been removed. The core is easy to spot for is has two hoses sticking out, and, is encircled with clips or screws . Also make sure you remove the bracket around the two entry hoses if it has one. Thank you, Dana

Posted on Oct 04, 2009

  • 10 Answers

SOURCE: 2000 Hyundai Elantra, Heater Problem.

check the fuses

Posted on Oct 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why Not heat in Hyundai elantra 2003 and thermostat and heater core ready replace


make sure all the air is bleed out of system and the coolant is circulating.

Mar 01, 2015 | Hyundai Cars & Trucks

1 Answer

How do i replace the heater core on a 2000 hyundai elantra


That is a big job. 90% of the cars require the dash to be unbolted from the interior and pulled back to access the heater core box. Expect to spend 5 hrs or more doing this job. Or do the shortcut method here https://www.youtube.com/watch?v=aZPiRJTof4c

Jan 16, 2015 | 2000 Hyundai Elantra

1 Answer

Smell antifreeze in my 2011 Hyundai Elantra


The only component inside the car that carries antifreeze is the heater core. I have not heard of any such problems with the year car you have. Take it to any radiator shop (or trusted repair shop) and ask them to pressurize the cooling system. If it doesn't hold pressure, you have a leak somewhere that should be apparent with pressure on the cooling system. It could be as simple as a loose clamp. If it were the heater core, you could feel the carpet where it touches the firewall. If it's wet and sweet smelling, you need a new heater core installed. Replacing the heater core requires quite a bit of disassembly and not something I would recommend for a typical backyard mechanic. Good luck.

Sep 22, 2011 | 2011 Hyundai Elantra Touring

2 Answers

I have a 2001 Hyundai elantra, and the engine temp sensor gets to the middle line, but no hot air blows. the fan blows cool air unless im at a higher speed around 70 mph, and even then there air is only...


2 things it maybe. Your blend door may be stuck open. 2nd Your heater core may need replacing. Check to see if both heater hoses are hot. 3rd heater control valve maybe bad. Good Luck!!!

Nov 03, 2010 | 2001 Hyundai Elantra

1 Answer

Change heater cord on 2005 hyundai sonata


You first have to drain the radiator, then you diconnect the heater hoses to your heater core .in the engine compartment. Then you remove the cover off the heater core assembly under the passenger side , under the glove box. Then you take straps off the heater core off. and replace . Install every thing you removed previously and refill your radiator and your done.

Apr 11, 2010 | 2000 Hyundai Sonata

2 Answers

Remove and replace heater core


how to change a hearter core in a 2002 hyundia elantra?

Jan 31, 2010 | Hyundai Motor 2002 Elantra

1 Answer

Where are tthe heater hoses located on 2000


Usually you open the hood. By the firewall you will see 2-hoses almost side-by-side that go in the middle of the firewall. Those two are the heater hoses.

Oct 26, 2009 | 2001 Hyundai Elantra

1 Answer

Does not heat in idle


is the heater fan working

Jan 20, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

501 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...