Question about 1994 Ford Thunderbird

1 Answer

No heat I have no heat the blowersruns,can change temp. setting and the car temp is ok.

Posted by on

  • yadayada
    yadayada May 11, 2010

    this is caused by the air temp control blend door actuator motor being defective,($25 part) it can be changed without removing the dash as the factory manual says, u must remove the glove box door and liner, it is very hard to get at and best left to the dealer.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 130 Answers

Under the hood is aheater control valve fell both heater hoses make sure they are both warm if not this valve is your problem

Posted on Feb 10, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

When I set the temp on 90, why is there no heat?

A possible plugged heater core or thermostat stuck open.

Jan 09, 2016 | 1999 Ford Explorer

1 Answer

No heat

could be a temperature sensor or switch but not the temp sensor for your temp gauge

Dec 10, 2012 | Cars & Trucks

1 Answer

Peugot 407 heater not working

You more than likely have a problem with the temperature control blend door inside the air ducting, this door sits between the heater core and the AC evaporator core and mixes the air for the desired temp at the registers/vents. More than likely it is sticking due to being warped from heat. To replace this door and its actuator requires the dash be removed from the car.

Feb 08, 2012 | Cars & Trucks

1 Answer

No heat, over heating

Not all new thermostats are actually working thermostats.It may require a second one.However,if the fan does not work it will be hard to tell.Is there a fan belt running to it?The goop that was added to it could actually plug up the the rad coils or rods and make it extremely hard to cool itself.It needs to be flushed.

Jan 22, 2012 | 1996 Subaru Legacy

2 Answers

Heat only works at 3000 rmp after car has come up to temp. If rpm drops below 3000 heat temp at vents will drop. Have changed the thermastat with no positive results. Temp gage has shown a quicker rise in...

Is the coolant level ok? After replacing the thermostat, did you bleed the air from the system? The bleeder should be at the front (on engine near radiator). Low coolant level, or air in the system can cause what you describe.

Dec 03, 2009 | 2002 Acura 3.2TL

1 Answer

My heat blow cold some body told me i need resistor on a 91 Buick regal unlimited where do i find it

the resister only changes the fan speed
if you have not heat
first check coolant level if it's down then you have a leak that will cause no heat if it's ok
then run the vehicle and make sure the engine temp gauge reads about half if not change the thermostat if the engine temp is ok
then grab the heater hoses see if they are hot then the heater core is plugged and if the heater hoses are hot
then there is a problem with the heater control head
hopr this helps

Nov 08, 2009 | 1991 Buick Regal

2 Answers

Heat does not work. coolant level ok and temp is ok

Might try checking the temp blend door operation or the temp blend door actuator. If all good there perhaps the control head itself is faulty.

Oct 08, 2009 | 2000 Jeep Grand Cherokee

1 Answer

No heat in the car

Check louvers that allow air through the heater core ducts. You should hear them move when you change from cold setting to hot setting on temperature dial. Listen closley to the ductwork.

Jan 18, 2009 | 2005 Hyundai Elantra

2 Answers

Temp control switch does not regulate temp i get heat on all settings except max ac

switch prolly not bad but you might wanna look into your heater control valve. valve not closing and letting the hot coolant fill your heat exchanger rather than recycling it back to the cooling system. The heat is over powering your a/c system and you're only getting a bit of cooling when you have the a/c on max. try it out

Jul 20, 2008 | 1996 Ford Explorer

Not finding what you are looking for?
1994 Ford Thunderbird Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers


Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides