Question about Ford Cars & Trucks

Open Question

Key broke in ignition. how do i hotwire 1973 ford pick-up

1973

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: key ignition aerostar ford van

had same problem and found out what remained of my key that was not in ignition still turned the car on by stiking whatremained in ing. If you can still turn the ing. on then it is easy to get the whole ing. switch out. Thier is a little pin under the switch. Turn ign. to on and use something that will fit that pin. Push the pin and pull out the ign. then if you can't shake it out then try pliers or a strong magnet

Posted on May 26, 2009

Ad
BearWeb
  • 357 Answers

SOURCE: ignition switch keeps spinning

Hi there,
Here are a few methods of how to do this, please read carefully!
Method 1

  1. Open the hood.
  2. Locate the red coil wire. Both the plug and coil wires are located at the rear of almost all V-8 engines. Four-cylinder engines have them placed on the right side, near the center of the engine. Six-cylinder engines are the opposite: left side, near the center of the engine .
  3. Locate the battery (it's the thing that looks like a battery).
  4. Run a wire from the positive side of the battery (not negative!) to either the positive side of the coil, or the red wire that leads to the coil. This will give power to the dashboard, which is essential if you ever want it to start.
  5. Locate the starter solenoid. On Fords, it is on the passenger-side fender well, near the battery. On GMs, it is on the starter under the steering wheel.
  6. If under the steering wheel, enter the car without setting off any alarms. If it has standard transmission, make sure the car is in neutral and the parking brake is on.
  7. Unlock the steering wheel by taking a flat blade screwdriver and placing it at the top center of the steering column. Push the screwdriver between the wheel and the column, then push the locking pin away from the wheel. Don't worry, you're allowed to be rough here. The locking pin will not break or set off any alarms. The solenoid should be underneath.
  8. You will see a small wire at the top of the solenoid and the positive battery cable below. Cross the two different terminal that they are connected to with a screwdriver or pliers. This will crank the engine, giving you leave to drive. Congratulations.

Method 2
  1. Enter car. Do not break into a car unless you own it and have documentation to prove it. Be aware that forced entry will set an intrusion alarm off if the vehicle is so equipped.
  2. Determine if the steering column and gear selector can be overridden, if so equipped. Serious damage to the shifting mechanism and/or steering column will result in forcing these theft deterrant mechanisms in an attempt to override them.
  3. Look under steering wheel. This may require taking an access cover off. These are usually held in place with concealed clips or #2 Phillips type screws. Remove if needed.
  4. See if there is a clip or wiring harness connector in which you can gain access to the wires behind the ignition.
  5. Look for the two wires that are the same, usually red and strip them and twist them together. One of these will be the primary power supply for the ignition switch, the other will be the connection for the vehicles electrical circuits that are energised when the key is turn to the run position. Connecting these will provide electricity for the ignition components, so the engine is able to run when the starter is turned.
  6. Strip about 1 inch of insulation from this pair of wires, and twist them tightly together. Wrap with electrician's tape if available, and do not allow them to short against metal vehicle components.
  7. Get the ignition wire, brown in many cars, strip it about 1/2 inch, and touch the end of the stripped brown wire with the connected red wires.
  8. Do not twist the brown wire to the reds, just touch the wires until ignition has been achieved.
  9. Rev the engine enough so you don't stall and have to do this process again.

Method 3 This is the most effective method due to the fact that you don't need to bother keeping wires together, raising the hood, or unlocking the steering wheel. If you hotwire it with the wires only, your steering wheel WILL NOT TURN unless you break the steering lock. The "classic screwdriver method" where you put a screwdriver in the lock and twist doesn't work because you can't generate enough torque with your bare hands to make the lock pins break off without breaking the lock off of its mounting structure, thereby rendering the car useless. Use this method instead.
  1. Gather materials: 1 flathead screwdriver with an insulated handle, 1 cordless drill and a small drill bit.
  2. Take it from an expert: So, there is a flap at the end of the keyhole. Position the drill on the keyhole about 2/3 of the way up and drill in about the length of a key. This will destroy your lock pins and make the key switch able to be turned on and off without a key. Every pin has 2 sections, followed by a spring, so drill it more than once, removing the drill each time to allow the bits of the lock inside to fall into place.
  3. Put the screwdriver in the same way you would put your key in, it doesn't have to go in deep because the pins are already broken.
  4. Use it the same way you use your key, just turn it.
    • Warning: this method will destroy your key switch and make it so anyone with a screwdriver or an exceptionally strong fingernail to steal your car.
Tips
  • Use this knowledge responsibly.
  • Vehicles with a computer chip in the ignition switch cannot be hot wired, the chip enables the ECM to function, and without it, the car will not run.
  • You risk causing significant damage to your vehicle if you hotwire it.
  • Never leave the ignition wires twisted together when you finish running the engine. This can burn up the ignition system of the vehicle, and will at least discharge the battery.

Warnings
  • If the ignition wires separate while driving, the engine will instantly die, and you may find yourself without power, steering, or brakes.
  • Don't use this in an illegal manner, such as to steal a car. Chances are you'll be caught, and prison is not a fun place.
Thank you for using FixYa! Have a nice day and please remember to rate this solution.

Warm regards,
BearWeb

Posted on Dec 29, 2009

SOURCE: key broke inside ignition 99 ford mustang do we

You'll have to get the broken piece out

Then buy two or more keys at the dealer, and then,insert into ignition ,and program,assuming you have an owners manual to look that up

Posted on May 16, 2010

  • 56 Answers

SOURCE: 1973 Ford Mustang Coil Hook-up

The wire that comes from your distributor hooks up to the Negative side of the coil. The other wire should be a switched positive that hooks up to the Positive side of the coil. It should be hot only when the key is ON or Start.

Posted on Jul 05, 2010

dj_relly999
  • 4070 Answers

SOURCE: how do i hotwire a 95 ford explorer......how do i

Hi and welcome to FixYa!
If you want to hotwire the car, please use a screw driver to connect both positive and negative of the starter. This will start the car without using the ignition.

Hope this helps and thank you for using FixYa! Have a good one!

Posted on Dec 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to start a Ford Contour with out my key


Probably can't be done if it is late enough to be fitted with a security system. In that case the key will have a coded transponder which the system will recognise and send a signal the the engine management to switch it on.

You either need a correctly coded key or remove the engine ECU and have it decoded.

Jan 23, 2016 | Ford Cars & Trucks

1 Answer

2008 Sonata. How do I remove the ignition switch?


  1. How to Remove and Replace an Ignition Lock Cylinder ...

    ? 5:13
    www.youtube.com/watch?v=S9I4MnRIrHk

    Sep 2, 2012 - Uploaded by RatchetsAnd Wrenches
    looking to take out ignition switch on a 1973 Porsche 914 ... key from a Hyundai Tucson 2008 .... the key was cold and broke in the ignition ... Going to try to change out my 2008 sonata using this as a guide. wish me luck.


Jul 10, 2015 | Hyundai Cars & Trucks

2 Answers

I need help to hotwire my car to bring it home...my key broke...help. please


tell you right now,call and get a tow truck,you are not hotwiring that car unless it is old school ignition.AND YOU DIDNT EVEN TELL ME WHAT MAKE AND MODEL,LMAO!!!

Apr 15, 2015 | Cars & Trucks

1 Answer

Someone broke into my 1999 grand am ruined ignition switch and plug ins need to know how to hotwire


You won't be able to hotwire it due to the passlock antitheft system. Read about it in this link.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Nov 16, 2011 | Cars & Trucks

1 Answer

1973 Ford Mustang Coil Hook-up


The wire that comes from your distributor hooks up to the Negative side of the coil. The other wire should be a switched positive that hooks up to the Positive side of the coil. It should be hot only when the key is ON or Start.

Jul 02, 2010 | Ford Mustang Cars & Trucks

1 Answer

Hi i need to know how to hotwire my XG Falcon Ute with smartlock


Get your ignition lights on for 30mins and car will start, if you use another ignition and key and leave ignition lights on for 30 mins the computer will configure and code new key!!!

Jan 01, 2010 | 1983 Ford Fairmont

1 Answer

Need a diagram for the ignition wires. The key was broke off in the ignition


you dont need a diagram because they should have a wiring plug down the line or get a thin pick and pick it out

Aug 16, 2009 | 1989 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...