Question about Cars & Trucks

Open Question

Ford Lynx SV gauge meters, L/R signal lights not working after brake oil was topped up. What's the cause and the solution?

The brake signal light was on while driving. Went over to service center and they topped up brake oil. Was alright for sometime. Next day, the whole odometer wasn't working. Digital km gauge (odometer) is on. Dashboard lights on. Door open signal works fine. Left & right signal lights not lighting but double signal lights work fine. Wiper works fine. Fuel & Temperature, Speed, RPM gauges not working.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 170 Answers

SOURCE: I need to change light bulb for drive Km in

YOU WILL NEED TO REMOVE THE DASH CLUSTER AND REPLACE THE GLOBE FROM BEHIND

Posted on Sep 01, 2009

Ad
jubes garage
  • 7 Answers

SOURCE: Dashboard meteres won't work such as speedometer,

i had the same problem you might try this. remove the rear seat you will find 2 fuse blocks the one closer to the battery is the one. if you have the owner manual locate 10 amp fuse # 37 known as IP1 AKA
instrument panel power module, if you do not have the owner manual it is the fuse 2nd row from battery 3rd up

Posted on Jan 25, 2010

  • 1 Answer

SOURCE: Check gauge light is on

Check the ground out at the thermistate housing area. Put a new wire loop end if needed . but clean with wire brush or sand paper if it is on the housing . Try moving to the intake itself . Try this before tring a computer. Good Luck!

Posted on Mar 28, 2010

  • 973 Answers

SOURCE: Everything works fine on my vehicle EXCEPT today

Check the fuse for those items that don't work.

Posted on May 28, 2010

  • 4793 Answers

SOURCE: unknown light indicator in the dashboard

it is a rear bulb failure light,have you checked the reversing light bulbs...?

Posted on Jun 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Nissan Altima 3.5L BATTERY LIGHT went on during 15 minute drive. Next day car "died" while idling after a 20 minute drive. BRAKE WARNING LIGHT & BATTERY LIGHT on prior to full electrical failure.


Start with checking the alternator voltage with a multimeter. With the car off check the voltage in the battery which should be holding 12v charged less if flat of course then start the car and test the battery again. If the alternator is good you should be getting a reading of 14 to 14.5 v if it's the alternator it'll A) not put any charge into the battery or B) be a very low voltage being anything under 13.5 v

Sep 30, 2016 | 2004 Nissan Altima

1 Answer

What causes fuse for signals to blow when activated and the signal lights light up when breaking on a E 150 Ford van?


Hi J.D.
The signal lights and the brake lights usually use the same filament in the bulb. If there is a bad ground on the rear lights, the current can go back through the signal light circuit and cause weirdness to happen.
If the fuse blows you net suspicious of a dead short which allows more current than intended.
I would recommend using a continuity meter and a voltmeter and doing a function check of the different parts of the circuits involved.
Hope this helps.
One last idea...... Has any maintenance been done on the wiring or lights recently? Something had to happen between when it worked, and when it didn't. That's what we're trying to find.
Cheerfuls

Nov 25, 2015 | Ford Cars & Trucks

4 Answers

Brake lights not working on my 1985 ford f150 after I replaced the brake switch


disconnect turn signal switch wires @ column, put power to wires to brake lights. that cks wiring to lights. next put power to wires through turn signal to ck switch. Power runs from brake light switch to turnsignal switch, to lights.

Oct 18, 2014 | 1985 Ford F150

1 Answer

ELECTRICAL ISSUE IN SUBURBAN


if the bridge (three diode that turn AC current to DC in alternator) is bad it causes internal draw

Jun 19, 2014 | Chevrolet Blazer Cars & Trucks

1 Answer

1990 Ford f250 brake lights and turn signals won't work - checked all fuses, flasher and bulbs and all are good, what could problem be??


Well the brake light and turn signal circuits are on two different fuses, but they both go thru the turn signal switch.
So I would start by checking for power in and out of the turn signal switch for each circuit.

Apr 07, 2013 | 1990 Ford F250

1 Answer

Some dash lights on my 01 ranger don't work.the bulbs are good


Get an Auto Electrician to trace and fix the problem. There are partial contacts in the wiring system.

Dec 29, 2012 | Ford F-250 Cars & Trucks

1 Answer

Reverse light work but brake light and rear turn signal doesnt


If your brake lights and turn signals are out, you most likely have a blown fuse, burnt bulb, or a problem in the steering column.----------------------------------------------------------------------
digimaster iii

Dec 21, 2012 | 2002 Ford Explorer

1 Answer

2004 gmc denali: backlit dash lights do not work


Check your bulbs first, I have lost both headlights on my ford at once on account of the bulbs burning out at the same time. Same thing probably happen, you have one filament out. The lights can work, but if the filament for brake is burnt, you don't see brake lights.

Sep 12, 2012 | Cars & Trucks

1 Answer

1995 Ford f250 brake lights don't work ad neither do the hazard flashers. I replaced the flasher node and the turn signals began to work but still no brake lights.


You may have a bad signal switch..Your brake lights run through the signal switch..Try hitting the brakes and move the switch around and see if your brake lights come on intermittently..

Sep 22, 2011 | 1995 Ford F250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...