Question about 1991 Dodge Spirit

1 Answer

91 dodge um ok but how much does it coast to replace and is the job tuff?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers


this is the relay that you need. it is pretty self explanitory as long as you have some basic technical back ground. Just find the part that looks like this one and replace it. Hope this helps.

Posted on Oct 24, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I was driving my manual 91 dodge stealth home when i went to shift into 4th gear the clutch pedal went all the way to the floor and stuck and now it doesnt like to go into gear with the clutch in but it...

Clutch disk or pressure plate or both are worn out, and I would replace the throw out bearing. You can buy a kit at autozone or kragen that has everything all together 100-200 dollars.

Aug 10, 2013 | 1991 Dodge Stealth

1 Answer

I have a broken exh bolt the needs to come off

THIS is a tuff job that nobody likes,its real easy to break another one,or more.....Have a real Good Socket that Fits Right..Good Luck!!OK...

Aug 02, 2010 | 1994 Ford F250 Supercab

2 Answers

Loosing power got a short connection between battery and altenator. Not sure if this is the problem

use agood size wire or small cable and run from large post on back of alternator to hot post(positive)of battery ,this will do the same thing sometimes they put ome parts that just get buy to do the job,this will do the job if not replace alternator

Jun 30, 2009 | Dodge Dakota Cars & Trucks

1 Answer

91 dodge all wheel drive

The only real differences between AWD and FWD are the transmission, rear axle and the driveshaft that connects them. There may be a different ECM for for engine tuning, but replacing the transmission and rear axle with FWD parts will accomplish what you want to do (transmission for your engine size). This is a big job, not for a DIY tune-up guy. If you just don't want AWD, remove the drive shaft to the rear axle.

Jun 01, 2009 | 1991 Dodge Caravan

1 Answer

Getting turbo off a 2001 dodge ram 2500 series to replace it

The tuff part is getting to the nuts that clamp the exhaust housing to the exhaust manifold. You may need to modify (heat up and bend) some wrenches to get them all off. Be sure to prime the new turbo before running it.

Apr 06, 2009 | 2001 Dodge Ram 2500 Truck

1 Answer

How do i change the heater core on my 91 dodge dakota??

not a job for the faint of heart. picture the whole dash board, right up to the windshield sitting on the seats,that kind of gives you an idea. no fun to do. the dealer gets about 8 hours for the job

Mar 29, 2009 | 1998 Dodge Dakota

1 Answer

Blown tranny in 60 KM 91 dakota let me down

hi, ok. if your torque converter is full then, you will need 5 qrts. if the torque converter and tranny is bone. it will need 8 qrts.

Feb 26, 2009 | 1991 Dodge Dakota

1 Answer

My son went through a puddle and hydrolocked his engine. Air intake had water in it and spark plugs were wet. Dodge says crank turns nicely by hand, however #1 piston not working and found piece of #1...

ouch, sorry to hear that. i have seen that many times. and the easiest thing to do is yes install long block. but there are more choices to take, here is my thought. OK so they say number one is in the oil pan ? so they removed the oil pan ? OK well then how do the cylinder walls look ? um OK are the scratched ? scored or is the a huge gouge on the cylinder wall ? OK if the wall is OK then the piston took the hit ? they need to do their job not just shot gun it. have they took a borescope in through the spark plug hole ? to look for damage ? if the piston and rod are damaged and nothing else then replace the piston and rod. they are trying to get ya for parts. careful here cause they may get mad and jack the labor. stay calm and get several bids for the job. us techs are starving right now as well as the small shop owner. use this and take a loss for diag at the current place if ya have to. you would prolly save money at a machine shop type of auto repair who does machine work in house. good luck

Jan 27, 2009 | Dodge Ram 1500 Cars & Trucks

2 Answers

Transmission will not up shift

91 subaru will not upshift in drive, stays in 1st. Will manually but only to 2nd. If you go to drive after that it coasts.

Aug 26, 2008 | Dodge Grand Caravan Cars & Trucks

Not finding what you are looking for?
1991 Dodge Spirit Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

78238 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides