Question about 1995 Chevrolet Camaro

1 Answer

I changed my ignition out of 95carmaro put a 93 carmaro ignition in it want crank what else i need

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,182 Answers

My guess is that you have interupted the antitheft system by switching out the ignition. Here is a link that will explain the problem, and offer ways around it.
In most GM cars and trucks there is a hidden system that most people are unaware even exists. From the moment you put your key in the ignition, there begins a constant line of communication between your key's security chip or transponder, to the ignition's lock cylinder, and then to the car's TDM. (Theft Deterrent Module) The TDM is what tells your computer that the correct key is being used and that it is "OK" to allow the vehicle to start and run. These 3 parts must be in CONSTANT communication. If the key is in the ignition, then these parts are sending important signals to each other. The security light illuminates when that signal gets broken, even just for a second. When the signal breaks, (normally due to a failing/broken part) the car goes into antitheft mode. The car misinterperates this and thinks its being stolen or hotwired because it is NOT getting that signal from YOUR specific key. There is where the security light turns on and shuts down your vehicle. So basically, if that light is on, your system has some sort of failing part. This can start as an intermittent "no start", to your vehicle not running for days at a time, to the vehicle NEVER starting again. The problem is electrical and computer based, so don't count on an easy reset button, or the problem fixing itself. The hard part is isolating which part is the problem. You can spend a thousand dollars through a mechanic very easily. I have had great luck with bypassing the entire system. This way the problem will never return. It actually CAN'T ever return because it is eliminated. This can also be done yourself at a much cheaper cost. Read through this link very carefully. You'll find alot of information and pictures, along with ways to help you fix this.
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Posted on Feb 13, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Died while driving, cranks, but no spark.


one of the reasons that engine stop while being driven is a failed timing belt or chain
that affects the cam/crank position sensors and so there is no spark allowed
so run the fault codes first and check that the cam shaft is turning when it is cranking

Sep 24, 2015 | Cars & Trucks

2 Answers

93 Jeep Grand Cherokee, no spark from ignition coil


so gue$$ stinks sure.... why do that.?
all it takes is a scan tool to find this.

first you need to learn ASD relay rules.
to start a jeep 1993 to NOW.
the ASD most close, cranking,does it?
and most stay closed cranking and NOT drop out in 3 seconds.
that means crank for 5 seconds and if the ASD drops. at 3.?
easy huh?
if it did DROP i can tell you the ECU will set DTC errors you failed to see because you did not scan it during those 5 seconds.

http://www.fixkick.com/Jeeps/ASD.html

first is fuses.
lets make a list. works on all jeeps 93+
  1. battery changed. to 12.6vdc reseted.
  2. keyon, CEL lamp glows, if not fuse blown to PCM (ECU)
  3. engine cranks fast.
  4. Asd realy pulls in and holds.
  5. scan tool shows, what? BINGO. DTC errors, easy huh?
  6. ok no DTC, errors, live for 5 seconds, cranking,so lost spark? must be bad coil or wired wrong. (change it 1 wire at a time?ooops)
  7. coil dead, its not DTC caused, so if no DTC that means the PCM did not see Coil ignitor errors. to coil see? i bet its got TDC;s if not then i check the coil inputs. to be sure the PCM ignitor is firing the coil correctly with my scope, oops no scope.
  8. if no scope you get to buy a new PCM. Wild guessing bad ignitor.
  9. i use a Innova 3140 scan too that does 93-95 jeeps, for about $150 only about 1.5 hrs shop labor value. and is Investment grade tool, it would have saved you 3 parts, guessed already.

Mar 18, 2015 | 1993 Jeep Grand Cherokee

1 Answer

93 ford f150 5.0 302.. Drove it for a week truck would crank wouldn't start then started drove it for another week now same problem.. Changed gas filter plugs wires distributor rotor ignition coil and...


Once it starts does it run OK or does it take a while to "come out of it"? What is the weather like? How is it acting when it wont start; does it turn over, if it cranks does it fire at all or no ignition at all, do you smell gas while it is cranking?

Oct 28, 2013 | Cars & Trucks

2 Answers

I have a 93 Eagle Talon with good fuel pressure and no spark


could be crank & cam sensor if they do not meet in sinc they will not get spark

Nov 13, 2009 | 1993 Eagle Talon

1 Answer

93 jeep burns out crank sensors


SONDS LIKE YOR ALTERNATER IS OVER CHARGING REPLACE THE INTERNAL REG

Aug 31, 2009 | 1999 Pontiac Grand Am GT

2 Answers

No spark no FI pulse NO START


Check the ignition switch please. Had that on a 93 Ford that it was bad and the coil wasnt getting any electricity while the switch was in "start" position.

Aug 17, 2009 | 1994 Ford Escort

1 Answer

The f150 93 truck won't crank unless relay is jumped


I had this problem on my F250. I actually just ended up putting in a switch that by passes the relay and brings power directly to ignition. Turn off switch so you dont drain battery, and turn on switch to start car.

Feb 26, 2009 | 2006 Ford F-150

1 Answer

93" subaru legacy ( EJ22 with auto) engine stopped & won't start


Water introduced through the fuel system. Drain tank and lines, refill, and add HEET.

Dec 26, 2008 | 1995 Subaru Legacy

Not finding what you are looking for?
1995 Chevrolet Camaro Logo

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...