Question about Cars & Trucks

Open Question

Nissan n13 brake master cylinder diagram - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 232 Answers

SOURCE: Spongy brakes after bleeding them 2 times. Should I try to bleed the master cylinder or replace it?

Honestly your guess is as good as mine. But I don't think the master cylinder is NOT bad you still have air in the system. Get a big bottle of brake fluid bleed all four sides until you run out of fluid or your brakes work properly. You should divide the bottle's content in four, then use each quantity in each side. You'll be removing air and contaminated fluid from the system. Get a small hose that fits on the bleeders and an appropriate container. I have a good feeling if you do this your brakes will work just fine. I don't know how you are bleeding the brakes. I'll let you know the proper way just in case. This is a two man job, with the wheel off, have someone start the car. Have them pump the brakes a few times to get pressure. 1With the brake pedal UP open the bleeder, 2then have your assistant press the brake pedal all the way down and leave it completely pressed down. 3Close the bleeder valve, once close and only with the valve closed have'm release the brake. Repeat as necessary, bake depressed, open valve first then press brake. DO NOT depress until valve completly closed. Close valve THEN depress. Good Luck!

Posted on May 15, 2009

Ad
mkv0525
  • 358 Answers

SOURCE: brakes are soft

must still have air in system or a bad new master cly.make sure you bleed all 4 wheels.could take awhile if you did not bench bleed the master cly first.

Posted on May 28, 2009

alicantecoli
  • 22326 Answers

SOURCE: instructions on replacement of a Nissan Pulsar N13 transmission?

manual or auto

Posted on Dec 19, 2009

duane_wong
  • 6826 Answers

SOURCE: 1997 ford escort brake line diagram

The LF and RR are in an independent circuit of the RF, LR wheels. The master cylinder already has the lines hooked up in a way that if you trace the lines, you can make your own diagram.

Posted on Aug 03, 2010

  • 2309 Answers

SOURCE: 1999 Nissan Quest. Driver side brake lock up. The

possible brake hose collapsing , interrior deterioration

Posted on Aug 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ive got a 1994 Nissan pickup 4x4 cant get brakes to bleed up and stay


may be bad master cylinder ~ you try to gravity bleed them first?

or you may have to bench bleed the master cylinder then re-install, gravity bleed to start

then finish off with the one-man bleeder or 2 person technique


i don't know how you did it, so i'm covering my bases by saying all that

Mar 17, 2015 | Nissan Cars & Trucks

1 Answer

How to replace slave cylinder on rear brakes of 1400 Nissan LDV


the slave cylinder is next to the master wheel cylinders are back there 2 / 10mm bolts hold them on

Sep 11, 2014 | Nissan 1400 Cars & Trucks

1 Answer

How do u replace the master cylinder on a 95 lincoln towncar?


  • Unplug the brake lines from master cylinder. Be careful with brake fluid spilling out, it is toxic and corrosive.If needed use a plastic container to collect fluid.
  • Disconnect electrical connectors.
  • Unscrew the nuts securing the master cylinder to the brake booster.
  • Remove master cylinder.
  • Perform procedure in reverse order to install the new master cylinder. After installation is complete, refill the master cylinder with brake fluid and perform brake bleeding procedure.Use only brake fluid stated in manufacturer specifications.
Here a diagram. The master cylinder is part 10 below reservoir part 9:

ginko_310.gif

Sep 08, 2011 | 1995 Lincoln Town Car

1 Answer

Why does my brake light indicator stay lit on my 1992 nissan stanza when parking brake is not engaged?


  • The majority of the time this is also an indicator that your brake fluid is below a safe level. Adding some brake fluid to the master cylinder and pumping the brakes a few times should remedy this.
  • If this does not remedy this then you have a leak in the brake system somewhere or your master cylinder could be malfunctioning. Make sure the lid on the master cylinder is on tight and sealed well too.
  • The master cylinder is where you fill the brake fluid. Do not over fill it.
Regards, tony

May 22, 2011 | 1992 Nissan Stanza

1 Answer

Brakes dont work, changed master cylinder, calipers ,brakes, brake booster... still no brakes at all . 2000 nissan xterra


check for air in the lines ..bleed the air out in this tire order LR, RF, RR, LF, i hope u bleed the master cylinder ..che if the bacuum to the booster is good

Apr 24, 2010 | 2000 Nissan Xterra

1 Answer

Problem with brakes on nissan primera 00 2liter diesel


bleed master cylinder first and then furthest wheel away from master cylinder

Mar 22, 2010 | Nissan Z Cars & Trucks

3 Answers

I have a 91 nissan d21 and cnt find the slave cylinder or master slave cylinder?


The master is beside the brake master cylinder, between the brake cylinder and the fender. Follow the line down to the trans, it ends at the slave. Now that you know where they are... why do you want to know??

Mar 13, 2010 | 1991 Nissan Pickup

2 Answers

Where is the clutch slave cylinder on a 1992 Nissan sentra


usually attached to your transmission just follow the line from your clutches master cylinder which is usually beside your brakes master cylinder

Oct 19, 2009 | 1992 Nissan Sentra 4 Door

1 Answer

90 nissan pickup, is it neccesary to replace


No the master cylinder is for your brakes.And the slave cylinder only does clutch.

Aug 10, 2009 | 1999 Nissan Maxima

1 Answer

1991 nissan stanza brakes


Your master cylinder rear seal is most likely shot. Check to see where the fluid is actually leaking from. If it is coming from the rear of the master cylinder, flush against the brake booster, replace the master cylinder.

Sep 05, 2008 | 1990 Nissan Stanza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78238 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...