Question about Cars & Trucks

1 Answer

Change serpentine belt on 1995 chevrolet berretta

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Oreilly print will print out a routing sheet for you if its not under hood. if you have a spring loaded you will have to take tension off to install belt.

Posted on Feb 13, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: how to change the serpentine belt on a lumina euro 3.1??

I found on my 92 lumina 3.1 the easiest way to change the belt is to have two people handy (you and a helper) push the belt tensioner (which is more in the middle of the belt system, its the only thing that has give when pressure is applied) down (which will loosen the belt) have your partner slip the belt off the altenator (which should be on the very top of the belt system on the passenger side) and just pay attention to the way the belt is routed as you remove it, put the new one on (routed correctly) push the tensioner again have your partner slip it back over the altenator....and you have a new belt on with no tools :)

just pay good attention to the routing of the belt, and i also think there is a black cover over the belt which needs to be removed before the old belt can be taken off (if you dont see it at first you will find it) it has 3 bolts i think and also a diagram of the routing....

TIP: the tensioner will take some muscle to move down, and yes the belt is running over it....

Posted on Dec 08, 2008

  • 6982 Answers

SOURCE: Serpentine Belt

Generally there is a sticker under the hood, showing belt routing. If not, get a cheap (usually under $20) manual... not only will you learn belt routing, but tips on tensioner adjustment, necessary to replace belt. Even a cheap manual includes lots of stuff you may need to know in the future!

Posted on Dec 26, 2008

  • 57 Answers

SOURCE: 1995 buick rivera serpentine belt install?

look around under the hood , on the underside of the hood, sometimes the belt routing diagram is on a sticker also check a Chiltons Manual sold at auto pARTS STOReS or on the web

Posted on Jun 12, 2009

  • 14 Answers

SOURCE: Describe your 2005 Chevrolet Optra Problem

Remove the air filter housing and air hose. Set aside
Pull the 15mm bolt on the tensioner counterclockwise (towards front of car) and hold it there to loosen tension, and remove the serpentine belt.
With your 15mm wrench, unbolt the belt tensioner and remove.
Replace with new tensioner
Put serpentine belt back on.
Very easy! Be careful when releasing tension, becase if you let go of the wrench it will fly back and could hurt you.

Posted on Jun 24, 2009

  • 1392 Answers

SOURCE: serpentine belt in 1995 Cavalier

Here is your diagram. 42188358

Posted on Jul 29, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 1995 4 cylinder berretta backfires and hesitates

Check your timing sounds like you mght have a timing issue or a bad plug wire

Aug 24, 2012 | 1995 Chevrolet Beretta

1 Answer

I need a diagram for the serpentine belt


  1. Disconnect battery ground cable.
  2. Remove air intake duct from throttle body extension.
  3. Using a 1/2 inch ratchet, retract serpentine drive belt tensioner.
  4. Lift belt rearward, off water pump pulley, then remove belt from vehicle.
  5. Reverse procedure to install. Refer to Fig. 29 for serpentine belt routing.

Nov 19, 2010 | 1995 Chevrolet Corvette

1 Answer

How do you route a serpentine belt on a 1995 Chevrolet Caprice Classic without AC?

Buy proper belt for application.look under hood for dirgram.
I didn't think Caprice had a serpentine belt.

Sep 20, 2010 | 1995 Chevrolet Caprice

2 Answers

I need a serptentine belt diagram for a 1995 cavalier

Your car could have a 2.2L engine or a 2.3L engine, so here's both, hope this helps you.


Aug 10, 2010 | Chevrolet Cavalier Cars & Trucks

2 Answers

Loud humming/whining noise coming from engine

Remove the serpentine belt and check the pulleys on the front of the engine. There may be a bad idler pulley or other component. Replace the serpentine belt if it hasn't been done in a few years.

Mar 06, 2010 | 1995 Chevrolet S-10 CA Edition

1 Answer

How do you change the serpentine belt on a 1995 f-250 Diesel

e-mail me at and i will scan you a copy to put up. berrydalewolf

Oct 27, 2009 | 1995 Ford F250

1 Answer

Trying to change the serpentine belt on a 1995 Tahoe 5.7L- how do I release tension on the belt?

i don;t have this vehicle available to me but there should be an idler puller with an automatic tensioner, a 3/8 breaker bar or t handle should slot into the pulley, lift anticlock wise and remove belt.

Jan 25, 2009 | 1995 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides