Question about 2006 Chrysler Pacifica

Open Question

Adjust parking brake on 2007 pacifica

Replaced pads, rotors and shoes and springs in the rear brakes. I adjusted the pads out as much as I could so I just barely fit on the rotors. Now I don't get anything from the parking brake at all!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 154 Answers

SOURCE: Adjusting Padking Brake with 4 wheel disc brakes.

Hope this helps. This is out of the factory manual. Let me know if this works for you.
PARKING BRAKE NOTE: Tensioner adjustment is only necessary when the tensioner, or a cable has been replaced or disconnected for service. When adjustment is necessary, perform adjustment only as described in the following procedure. This is necessary to avoid faulty park brake operation.

  1. Raise vehicle.
  2. Fully back off cable tensioner adjusting nut at equalizer to create slack in cables.
  3. Remove rear wheel/tire assemblies. Remove brake calipers and rotors.
  4. Verify park brakes are in good condition and operating properly.
  5. Verify park brake cables operate freely and are not binding, or seized.
  6. Check park brake shoe adjustment.
  7. Reinstall rotors and make sure rotors turn freely.
  8. Reinstall brake calipers. Tighten guide pin bolts to 41 n·m (30 ft.lbs.)
  9. Reinstall wheel/tire assemblies after brake shoe adjustment is complete.
  10. Lower vehicle enough for access to park brake foot pedal. Fully apply park brakes
NOTE: Leave park brakes applied until adjustment is complete.
  1. Raise vehicle again.
  2. Mark tensioner rod 6.35 mm (1/4 in.) from edge of tensioner bracket Adjustment Mark On Cable Tensioner Rod
  3. Tighten adjusting nut at equalizer until mark on tensioner rod moves into alignment with tensioner bracket
CAUTION: Do not loosen, or tighten the tensioner adjusting nut for any reason after completing adjustment.
  1. Lower vehicle until rear wheels are 15-20 cm (6-8 in.) off shop floor.
  2. Release park brake foot pedal and verify that rear wheels rotate freely without drag. Verify pedal returns to fully released position.
  3. Lower the vehicle

Posted on Apr 03, 2009

  • 47 Answers

SOURCE: 2006 Pacifica emergency brake problem.

The only manual adjustment for the parking brake on these is at the shoes themselves. Procedure for that is as follows:

1) Place parking brake lever in "full released" position.
2) Raise and support vehicle.
3) Remove plug in parking brake shoe support to access adjuster star-wheel.
NOTE: Through the access hole, rotate the adjuster wheel in the following direction to expand the shoes outward against the drum.
Left brake--Rotate star wheel toward rear of vehicle.
Right brake--Rotate star wheel toward front of vehicle.
4)Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
5) Back off adjuster six detents (teeth).
6) Rotate wheel, checking for light drag. If drag is too heavy, continue to back of adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
7) Install access plug.
8) Adjust opposite wheel parking brake shoes using same method.
9) Lower Vehicle.
10) Apply and release parking brake lever once to ensure proper operation of parking brakes.

These directions are directly from 2006 Pacifica factory service manual. If you have any other problems feel free to ask. v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}
v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}

Posted on Mar 11, 2010

  • 3 Answers

SOURCE: chrysler voyager drum brakes excess hand brake travel no adjuster how can a take up slack

yes there are brake shoes in the hub. we have just replaced ours also links and still there is travel. mot just hours away, as failed last time. My hubby is now in pouring rain trying to adjust. Also the lever now only has a few clicks as adjusted cable at lever but still no handbrake at wheels.

Posted on Sep 05, 2008

MrScary66613
  • 1990 Answers

SOURCE: brake pad replacement 2006 pacifica

They have not Changed Very much from the Old School Disc Brakes. You should have no Problems! Please Rate My Response! Thanks!

Posted on Jan 31, 2009

SOURCE: how to remove the rear brake drum on a 1999 chrysler town & count

The star wheel is accessible after removing the elongated rubber plug on the drum housing right next to the brake bleeder screw. Use a "brake drum spoon" to rotate the star wheel one click at a time. The proper direction of rotation is the direction the star wheel does not want to go since you are turning it against the hold of the ratcheting no-back. After rotating it several clicks, jiggle and pull on the brake drum and if it doesn't slide off with a normal amount of force, rotate the star wheel several more clicks. If I recall, the star wheel only has about 25 clicks of rotation or so before even brand-new, thick shoes are backed off away from the drum a significant amount to the point that the auto adjuster has a considerable amount of slack in it (no outward pressure).

Posted on Apr 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The passenger rear brake makes a thumping noise when pushing the brake


Drums brakes. This could be an adjustment problem or a spring has broken. Slack adjusters do lock up from brake dust or rust.
Rotors. This could an adjustment for the E brake shoes, Or the pad has broken off the shoe. Also if a bolt broke or came out of the caliper.

Mar 03, 2016 | 2007 Mazda 3

2 Answers

Parking brake cable stretched beyond adjustment how do you replace


Rear Brake Shoes- You'll need to know how to remove the rear brake shoes to remove the parking brake cable. REMOVAL AND INSTALLATION Amigo and Rodeo
  1. Raise and safely support the vehicle.
  2. Remove the rear wheels.
  3. Remove the brake drums.
  4. Remove the brake return springs.
  5. Remove the leading shoe holding pin and spring, and then the leading shoe.
  6. Remove the self-adjuster and the adjuster lever.
  7. Remove the trailing shoe holding pin and spring.
  8. Disconnect the parking brake cable from the trailing shoe and remove the trailing shoe. Remove the parking brake lever from the trailing shoe. To install:
  9. Attach the parking brake lever to the trailing shoe.
  10. Connect the parking brake cable to the parking brake lever.
  11. Apply a thin coat of high temperature grease to the shoe contact points on the brake backing plate (locations A and C in the accompanying illustration), piston contact surface (B), and self-adjuster (D). Fig. 1: Exploded view of the rear drum brakes — Amigo and Rodeo 93026g56.gif

  12. Position the trailing shoe on the backing plate and install the hold-down pin, spring, and retainer. Don't stretch the return spring when fitting the shoes onto the backing plate.
  13. Connect the upper return spring and the leading shoe to the trailing shoe and position the leading brake shoe on the backing plate.
  14. Install the adjuster assembly and the hold-down pin, spring, and retainer.
  15. Use a brake spring tool to install the lower return spring.
  16. Install the self-adjuster lever and adjuster spring.
  17. Adjust the shoe-to-drum clearance to 0.0098–0.0157 in. (0.25–0.40mm) and install the brake drum.
  18. Check the brake drum for scoring or other wear. Machine or replace as necessary. Check the maximum brake drum diameter specification when machining.
  19. Install the rear wheels. Lower the vehicle.
  20. Road-test the vehicle.
prev.gif next.gif

Aug 17, 2010 | 1997 Isuzu Rodeo

2 Answers

How to remove brake rotors on a 1996 ford explorer


How to replace the rear brake pads on a 1995 through 2001 Ford Explorer The system utilizes a drum-in-hat type rear brake rotor. The integral drum allows the use of a drum-and-shoe type parking brake system. All other components are similar to their front disc brake components Remove the two bolts on either side of the brake hose with the rubber boots. Do not remove the four bolts where the axle ties in. The two bolts to be removed require a 10mm socket/wrench. Loosen the pads from the caliper Rotor Removal In order to take the rotors off (replace with new or have them machined), it is best to loosen the emergency brake shoes. To do this, behind the rotors, in the back there is a rubber plug, remove that and you can use a screw driver to engage the teeth of the adjusting screw, turn it clockwise to loosen, usually 10-20 teeth. Usually this means turn it downward. After this, it may still be difficult to get the rotors off without tapping them. Use a rubber mallet and hit them from behind. Before really whacking the rotor, make sure you have loosened the adjusting screw enough. It may take heavy swings of the rubber hammer to do this. It will eventually break loose. Parking Brake You might want to check the parking brake while you are here. To remove:
  • Remove the rear disc brake rotor.
  • Remove the outboard return spring.
  • Remove the adjusting screw spring.
  • Remove the rear brake shoe hold-down spring and pin.
  • Remove the brake shoe adjusting screw and nut.
  • Remove the front brake shoe hold-down spring and pin.
  • Remove both parking brake shoes and the inboard return spring.
  • Check the parking brake lever for excessive wear and replace as necessary.
To install:
  • Position the front parking brake shoe to the backing plate and install the hold-down pin and spring.
  • Install the rear parking brake shoe with the inboard return spring.
  • Position the brake shoe adjuster screw and nut on the shoes and install the rear shoe hold-down pin and spring.
  • Install the brake shoe adjuster spring.
  • Install the outboard return spring.
  • Adjust the parking brake shoes and install the rotor, caliper and wheel.
  • Lower the vehicle and tighten the wheel lug nuts to 100 ft. lbs. (135 Nm).
ADJUSTMENT
  • Measure the inside of the drum portion of the rear brake rotor
  • Remove the rear disc brake rotor.
  • Using Brake Adjustment Gauge D81L-1103-A or equivalent, measure the inside diameter of the drum portion of the rear disc brake rotor.
  • Subtract 0.020 in. (0.508mm) from the first measurement, adjust the brake shoes to that size
  • Adjust the parking brake adjuster screw until the outside diameter of the parking brake shoes measures 0.020 in. (0.508mm) less than the drum measurement.
  • Install the rear disc brake rotor.
Reassembly Reassembly is easy. Put new or machined rotors back on by sliding them over the lugs (they should slide on easily.) Loosen bleeder valve (having a catch bottle handy is good). Push calipers in slowly (using a c-clamp or large channel lock pliers), close bleeder valve. Put on pads. Lubricate metal clips with small amount of anti-seize. Re-adjust the emergency brake by turning the opposite direction from loosening. Refill the brake master cylinder

Aug 09, 2010 | 1996 Ford Explorer

1 Answer

Mazda miata 2003 replaced rear brake pads now parking brake does not work any ideas?


Doe's the back brakes work? Is number 7 and 15 hooked up right? If they are. Try backing up and hitting brakes, This will tigjhten them up.
1 – SUPPORT PLATE
2 – RETURN SPRING
3 – ANCHOR PLATE
4 – RETURN SPRING
5 – CABLE GUIDE
6 – PARKING BRAKE LEVER
7 – ADJUSTER CABLE AND SPRING
8 – SHOE RETAINER, SPRING AND PIN
9 – SECONDARY SHOE AND LINING
10 – LEVER SPRING
11 – ADJUSTER LEVER
12 – ADJUSTER SCREW ASSEMBLY
13 – SHOE SPRING
14 – PRIMARY SHOE AND LINING
15 – PARKING BRAKE STRUT AND SPRING e753404.png

May 24, 2010 | 2003 Mazda MX-5 Miata

1 Answer

Trying to remove rear rotor. removed spring clip and rotor is loose , but acts as if some unseen is holding it on. want to chek e-brake pads


yes, the e- brake shoes are holding it, some have a little window on the back of backing plate use a screw driver or adjusting tool to turn adjuster to loosen shoes then rotor will slide off, remember to adjust back, good luck,

Nov 26, 2009 | 2005 Dodge Caravan

3 Answers

Rear brake pads wear out every 30000 miles on 2002 3/4 tod hd , rotors are pitted bad


That's to be expected and is completely normal.

Rear brake shoes as fitted to drum brakes can typically last up to 60k miles with periodic adjustments, but you have rear disc brakes and the shoes will typically last half of that.

Also, modern brake pads no longer contain asbestos and are now made using harder metallic compounds; the direct result is that brake discs (US=rotors) are also considered to be consumable items as they are worn down by the harder pads. It's not unusual to have to replace front discs every other pad change and rear ones with every pad change; in both cases the mileage will typically be around 30k miles on most models.

Nov 15, 2009 | 2002 GMC Sierra 2500HD

1 Answer

94 landcruiser brakes


Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.


  1. Raise and support rear of vehicle, then remove wheel and tire assembly.
  2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
  3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
    1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
    2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
    3. On 2WD T100 models, proceed as follows:
      1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
      2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
    1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
    2. Remove adjusting lever spring, then the adjuster from front shoe.
    Inspection
    1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      1. On 2WD T100 models, proceed as follows:
        1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
        2. Assemble and install wheel cylinder.
        3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
        1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
            1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
            2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
            3. Install tension spring.
          1. Ensure proper parking brake travel.
          2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
          3. Adjust strut to shortest possible length, then install drum.
          4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS
  1. Remove caliper.
  2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
  3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
  4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
  5. Remove free wheel hub body and gasket.
  6. Remove locknut, lock washer and adjusting nut.
  7. Remove axle hub and brake disc as an assembly.
  8. Remove oil seal and inner bearing from hub.
  9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.
  1. Raise and support front of vehicle, then remove tire and wheel assembly.
  2. Remove clip and hole pins, Fig. 9.
  3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
  4. Lubricate caliper housing with suitable brake grease at pad contact points.
  5. Reverse procedure to install.

Jan 28, 2009 | 1994 Toyota Land Cruiser

2 Answers

Parking brake pedal goes to floor


Hello;
The parking brake cables may be stretched and in need of adjustment. Follow the cables along to a nut. Then you can tighten the adjusters up on both sides until you have the proper tension. Also make certain none of the brackets are bent or broken that the cables ride through.
Thanks;
RPM Northwest

Jan 19, 2009 | 2003 Chevrolet Suburban 1500

1 Answer

How do I reinstall the parking brakes on my 2001 GMC Jimmy.


hi from the uk not too conversant with your model ? BUT here in uk the same type of rear calipers for hydraulic disc brakes and a seperate set of brake shoes operate the park brake/s which is internal of the rotor ?? thebrake shoes will have an adjuster manually adjustment when rotor/drum is in place ? so if you look at the area between the top of shoes you may see a threaded rod with a serrated round wheel which when turned on thread will move shoes out one way and in the other ? so to fit rotor you must rotate this wheel so shoes close up enableing to fit rotor/drum over shoes easily ? then secure rotor with screws?? if fitted then you adjust ppark brake shoes by turning with a flat screwdriver via a hole which is/should? be in rotor and will turn in line with this adjuster? tighten brake on then turn back notch by notch till rotor turns free or just? do this b4 you fit the disc pads then repeat on other brake assy on other side? re assemble discpads and pump brakes till hard this then leaves the park brake cable to adjust if req'd if so pull p/brake it should come up approx 4 or 5 clicks to fully lock of brake this allows for what is known as reserve travel left on cable to apply as brake shoes wear ok? hope this helps?

Jan 16, 2009 | 2001 GMC Jimmy

Not finding what you are looking for?
2006 Chrysler Pacifica Logo

Related Topics:

658 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...