Question about 1995 Saturn Sl

Open Question

Need pattern for 95 saturnls2 1.9 head bolt

Torque pattern for head bolt

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
johnjohn2
  • 5763 Answers

SOURCE: looking for head bolt torque for 95 SOC saturn. im

The torque spec are as follows, step one is 22 ftlbs then step 2 is 33ftlbs and the third step is to tighten bolts 90degrees more also the bolt tightening sequence is here, this is a diagram of the bolts good luck and i hope this helps.johnjohn2_60.gif

Posted on Jan 10, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 corolla head bolt torque


A Chiltons/Haynes repair manual from your local auto parts store that covers your year/make/model has all of your answers under the "engine rebuild" heading.

Sep 23, 2014 | 2005 Toyota Corolla

1 Answer

Head torque and pattern


The S-10 had two (2) different head bolts, a long bolt and a short one . The torque on the long one is 46ft./lbs. and an additional 90 degrees . The short one is 43ft./lbs. and an additional 90 degrees .

Looking at the head from the front of the vehicle, follow this torque sequence :
Start with the center bolt on the passengers side (left side of the head), followed by the center bolt on the drivers side (right side of the head) . Then torque the bolt behind the center bolt on the passengr side . Next torque the bolt in front of the center bolt on the drivers side . Then torque the bolt behind the center bolt on the drivers side . Next torque the bolt in front of the center bolt on the passeger side . The torque the last bolt on the drivers side, followed by the front bolt on the passenger side, followed by the last bolt on the passenger side, and lastly, the front bolt on the drivers side .

Aug 24, 2012 | Chevrolet S 10 Cars & Trucks

2 Answers

Can't find the torque head bolt pattern for a 1996 gmc sierra 5.7 vortex


The "pattern" for ANY cylinder head is pretty much the same...start with the bolts in the center of the head and work your way out to both ends.
Torquing the cylinder head on your 5.7L Vortec engine to manufacturer specifications requires the use of a "torque angle" gauge, as well as a traditional torque meter.

The torque specifications are as follows:

> Step 1: All bolts: 22 Ft Lbs (30 Nm.)
> Step 2: Short bolts: Additional 55 degrees; Medium bolts: Additional 65 degrees; Long bolts: Additional 75 degrees

May 20, 2012 | GMC Sierra 1500 Cars & Trucks

1 Answer

2002nissan3.5cylinderheadtorque



2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Apr 12, 2012 | Cars & Trucks

2 Answers

I need lower manifold rocker and upper manifold torque instructions please help


Head Bolts
Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation.New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
The Intake Bolt Torque 10 Foot pounds (Final torque)
Note:to torque bolts & nuts, start in center using crisscross pattern working outward

Dec 05, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Need torque specs and sequence for 78 ford 400 cid cylinder head


1st step 75 ft/lb 2nd step 95 to 105 ft/lb - start at center two bolts and work out in a z pattern. IE if the bolts are numbered 10-6-2-4-8 (looking over the drivers side fender) on the outside bolts front to to back and the inner bolts are numbered 9-5-1-3-7 - tighten in that sequence. Hope this makes sence.

Nov 27, 2010 | Ford F-150 Cars & Trucks

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

1 Answer

Hi, I neeed to know what the torque pattern is for


If your installing a new head gasget, the torque spects and pattern will come with it. If not and you are installing a new head gasget you have to use new head bolts, the short bolts witch go in next to exhaust manafold are 43 ft. lbs. and the longer ones in the center of the head are 46 ft. lbs. start with the one in the middle by exhaust and next one in center of head next to it and do the rest in a circle pattern, after you got them all torque than you have to turn each one 1/4 turn, thats why you have to use new bolts that 1/4 turn stretches the bolts. If you don't understand this go to auto zones web sight thats where i found it. I just did one 2 weeks ago.

Aug 15, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

Need the cylinder head torque settings on a toyota corolla 1990 model ae92 wiht a 4a-fc engine


Tighten in several passes to 44 foot pounds.

I just wanted to add. Since this is an aluminum cylinder head, I hope you loosened the head in the loosening torque pattern. The pattern opposite of the torque tightening pattern. If not, you stand the chance of warping the head.

Again, since it's an aluminum head, it needs to be checked for flatness. Most aluminum heads need to be surfaced before re-installing.

Tightening torque pattern is as follows:

1.The Drivers side of the engine is the Left side.
From the Front going towards the back; the bolts are numbered 10, 6, 1, 3, and 7.
From the Front going towards the back on the Passenger side; the bolts are numbered 8, 4, 2, 5, and 9.

The Exhaust and Intake Camshaft Bearing Cap bolts go to 9 foot pounds. Tighten gradually. One bolt to the other with so many foot pounds, work back, and forth up to 9lbs.

Camshaft Timing Pulley bolts go to 43 foot pounds. (In a tightening sequence, and gradually)

Jul 25, 2009 | 1990 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...