Question about 2003 Ford Windstar

1 Answer

Windstar cmp sesor replacement - 2003 Ford Windstar

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 202 Answers

Say again the code ,,,,, cmp is not enough

Posted on Feb 13, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Dodge Stratus code p0340 cmp sensor Limited to 2500rpm in all gears fuel pressure is high it should be 47 to 51psi it reads 60 Replaced cmp sensor and fuel pump pressure is still high 58 to 59psi and...


code p0340 refers to camshaft position(CMP) sensor A bank 1---circuit malfunction===causes wiring---CMP sensor--ECM

code p0344efers to CMP sensor A bank 1--circuit intermittent===causes --wiring --poor connections ---CMP sensor---ECM
Check the wiring and connections and if ok then replace the sensor. Check air gap to the rotor and check that there is no dirt or anything else that can affect the air gap

Mar 24, 2014 | Cars & Trucks

1 Answer

Camshaft sesor location hyudia xg 350


no year, azera? why not name car?????
?
always on the the end of the cam.
but on a Toyota, XG 350, not a clue..... read blue box above,. ugh !
i will not do posts , no year, and get funky no country.. for most.
dig,dig ,bam
XG350 name was used as of 2002 to reflect the new 3.5 L version of the Sigma V6.
ok the 3.5L
i looked online and 9 engines, shows CMP but not 3.5L

autozoned
"On the 3.5L engine, the sensor is located at the front of the engine near the camshaft gear."
this engine has VVT with 2 sensors and 2 vvt solenoids
finding the real CMP is hard. sure.
part 39318 CMP
it exactly here, so you can find any part ad Hyundai. just look


http://www.jimellishyundaiparts.com/images/parts/Hyundai/fullsize/HMA3L0PA0520-21104.jpg

clear huh?
this is best covered with a REAL FSM
and if PCM is throwing codes, do not assume this part is bad
they rarely go bad... instead post the code. DTC.

what if the chain was loose. the sensor will read wrong,
just one lil, example.

Jan 23, 2014 | Toyota Tacoma Cars & Trucks

1 Answer

Where is the cam sensor on a 2001 gmc 3500 serria 8.1


  1. Raise and suitably support the vehicle.
  2. If the vehicle is equipped with the underbody shield package, remove the steering linkage shield.
  3. Disconnect the camshaft position (CMP) sensor electrical connector (3).
  4. Remove the CMP sensor bolt (2).
  5. Remove the CMP sensor (1).
  6. Inspect the CMP sensor for wear, cracks or leakage if the sensor is not being replaced.


9_27_2012_8_44_22_pm.gif
    Installation ProcedureImportant: Inspect the CMP sensor O-ring for wear or damage. If a problem is found, replace the O-ring. Lubricate the new O-ring with engine oil before installing.
  1. Install the CMP sensor (1).
    Important: The CMP sensor bolt has self-tapping threads, care must be taken, NOT to strip the threads when installing.
  2. Install the CMP sensor bolt (2). Tighten
    Tighten the bolt to 12N•m(106 lb in).
  3. Connect the CMP sensor electrical connector (3).
  4. Install the steering linkage shield, if equipped.
  5. Lower the vehicle.
  6. Sep 27, 2012 | 2000 GMC Savana

    1 Answer

    Engine light is on


    There are problems with the O2 sensors (2 of them in the front exhaust pipes directly behind and below engine manifolds for cylinder banks 1 and 2). The 2 sensors should be replaced as a set never just one.

    Dec 03, 2011 | 1998 Ford Windstar

    1 Answer

    Showing Code P1309. Replaced the cam sensor and still showing the code or CMP. What can it be?


    You may need to replace the PCM, engine computer. very rare issue. Personally, I would leave it. It is only there to tell you if a cylinder is not firing. You will know if one is.

    HD41 CHECK CMP SENSOR OUTPUT
    • Connect PCM.
    • Connect digital multimeter.
    • Start engine and vary engine RPM.
    • Measure voltage between CMP and PWR GND circuits at the PCM harness connector.
    Does AC voltage vary greater than 0.1 volt AC? Yes No VERIFY the correct installation by referring to the Electronic Engine Controls, Section 303-14 in the Workshop Manual. If CMP is installed properly, REPLACE PCM (refer to Section 2 , Flash EEPROM). REPLACE CMP sensor. COMPLETE Misfire Monitor Repair Verification Drive Cycle.

    ----------------------------------------------------------------------------------------------
    P1309 - Misfire Monitor Disabled When the misfire monitor is disabled, usually due to the input signal generated by the camshaft position (CMP) sensor, by sensing the passage of teeth from the CMP wheel.
    • Camshaft position sensor
    • Powertrain control module
    • ECT, MAF, and CKP sensors
    Verify the CMP is installed correctly and not out of synchronization.

    Aug 05, 2011 | 1999 Ford Windstar

    2 Answers

    Installing a camshaft sensor


    Replacing the Sensor 1. Disconnect the negative battery cable...just like on every other installation 2. Detach the CMP sensor connector next. 3. Remove the CMP sensor retaining bolt and remove the CMP sensor

    Now to install:

    1. Clean the CMP sensor surface and ensure that the O-Ring is in place. 2. Position the CMP sensor into the engine and tighten the retaining bolt to 71-106 inch lbs. 3. Attach the CMP sensor connector 4.Connect the negative battery cable.

    Apr 03, 2010 | 1997 Mercury Sable

    2 Answers

    Most common cause for code P0340 of 95 Ranger


    Hi, the cam shaft sensor will be located Under the hood, center, upper engine area, mounted behind rear of intake manifold, in the engine block.


    This is a magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.

    The possible causes of failure will be faulty housing or faulty wires as well. A faulty ECM could trigger a false alarm as well. this is highly unlikely but, possible in most cases. The most reported reasons is flat out sensor failure.

    May 21, 2009 | 2001 Ford Windstar

    2 Answers

    Camshaft sensor


    It is located at the right rear of the engine block. It has a plug with three wires in it. Hope this helps.

    Oct 21, 2008 | 1997 Ford Windstar

    Not finding what you are looking for?
    2003 Ford Windstar Logo

    32 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5470 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...