Question about Cars & Trucks

2 Answers

How to replace v - ribbed belt - Cars & Trucks

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 74,251 Answers

Hello
See this video.
Try these links too
share.qclt.com/.../2GR.../Drive%20Belt/00800210.pdf
http://www.dataentryjobs.us/67948.html

Posted on Feb 13, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,036 Answers

Which type belt working on. the V OR COGGED V TYPE BELT you need loosen alternator adjusting bolt and mounting bolt, the power steering pump,and the air conditioner compressor loosen adjuster bolt and the mounting bolt. if you have wide rib belt that drive everything you need a tensioner tool stick in tensioner square slot hole push tool forward it will unload tensioner enough to replace drive belt, if you have the idler pulley type tensioner place wrench in the center bolt in the idler pulley tensioner turn wrench forward should unload belt tension.

Posted on Feb 13, 2012

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mas66
  • 104 Answers

SOURCE: Isuzu Trooper V6 2001 multi rib belt replacement

They have an automatic tensioner, like a spring loaded pulley. They are usually quite easy to pull back using a power bar or spanner. For the routing diagram, click here

Posted on Mar 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 saturn serpentinebelt diagram


I had 4 saturns, 91-01, all of them had a little silver sticker in the engine bay with a belt diagram, also showing how to release tension to remove and replace the belt. further if you note the inside of the belt is ribbed, thus the belt goes around those pulleys which are ribbed, and the smooth back of the belt goes against those pulleys which are not ribbed.

Jun 26, 2011 | 2000 Saturn SL

1 Answer

When do I change the serpentine belt, how many miles


Hello: The guide for replacing the belt is if it is not frayed. then look at the ribs if there are many small cracks in the ribs its time to replace the belt.

Jan 19, 2011 | 2000 Chevrolet Silverado

1 Answer

My serpentine belt is missing ribs...how long can i drive on this?


WHEN DRIVE BELT MISSING RIBS OR HAVE CRACKS RUNNING PARALLEL TO V PORTIONS OF BELT.THE DRIVE BELT NEED REPLACING SOON AS POSSIBLE.

Dec 05, 2010 | 2002 Nissan Sentra

1 Answer

Need diagram for installation of a serpetine belt for 2005 Toyota Tacoma P/U 4.0. Please advise. Thanks


  1. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.1 (4WD AND PRE RUNNER DRIVE TYPE)
    1. Remove the 4 bolts, then remove the under cover No.1.
    2. dak408_42.gif
  • REMOVE FAN AND GENERATOR V BELT
    1. While releasing the belt tension by turning the belt tensioner counterclockwise, remove the V-ribbed belt from the belt tensioner.
  1. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
    1. Check that nothing gets caught in the tensioner by turning it clockwise and counterclockwise. If a malfunction exists, replace the tensioner.
    2. dak408_43.gif
    3. INSTALL FAN AND GENERATOR V BELT
    1. While turning the belt tensioner counterclockwise, align with its holes, and then insert a bar of 6 mm (0.24 inch) into the holes to fix the belt tensioner.
    2. Install the V-ribbed belt.
    3. While turning the belt tensioner counterclockwise, remove the bar.
    4. dak408_44.gif
    1. If it is hard to install the V-ribbed belt, perform the following procedure.
(1) Put the V-ribbed belt on all parts except the P/S pump, as shown in the illustration. (2) While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the P/S pump.
  1. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO.1 (4WD AND PRE RUNNER DRIVE TYPE)
    1. Install the engine under cover with the 4 bolts. Torque: 29 Nm (296 kgf-cm, 21 ft. lbs.)

Nov 21, 2010 | 2005 Toyota Tacoma

2 Answers

How do you know your serpentine belt on a 2006 nissan altima is going out


Serpentine belts should be replaced every 60k miles. You do not want it breaking while driving down the road. To inspect the belt look at the grooved side of the belt. If you see cracks in the rubber then I would replace it.

Sep 23, 2010 | 2006 Nissan Altima

1 Answer

How do I replace a serpentine belt on a 2004 Prius?


Removal & Installation
  1. Remove the engine under cover.
  2. Loosen the clamp, then disconnect the air cleaner inlet from the air cleaner case.
  3. Referring to the illustration, loosen nut A, then turn adjust bolt B to relieve the V-ribbed belt tension.
  4. Remove the belt.

d5d0f8c.gif
V-belt removal

To install:
  1. Install the V-ribbed belt to each pulley.
  2. Turn adjust bolt B to adjust the V-ribbed belt tension.
  3. Tighten nut A to 40 Nm (30 ft. lbs).

May 05, 2010 | 2004 Toyota Prius

1 Answer

Serpentine belt diagram for 1996 audi a4 quattro v6. I can't find a proper diamgram and install procedure, can you help?


Ribbed Belt: Service and Repair
Ribbed Belt, Removing and Installing
Ribbed belt, removing and installing
CAUTION: Mark the direction of belt travel before removing, using a crayon or marker. Reinstalling a used belt in the opposite direction
could damage the belt
Note:
There are two different types of ribbed belt, identified as versions A and B.
Ribbed belt versions, identifying, refer to Application and ID
Removing
Old version A
- Remove ribbed belt guard.

4f56130.jpg
- Loosen ribbed belt tensioner using 15 mm wrench and drift 3204.
- Remove ribbed belt.

New version B
52631fe.jpg
- Using 10 mm hex socket wrench, turn downward in direction of arrow to loosen ribbed belt.
Installing
Install in reverse order of removal, noting the following:
- Place ribbed belt over drive pulleys and idler roller first, and onto tensioning roller last.
- Remove drift 3204.
- Install ribbed belt guard.

Sep 24, 2009 | 1996 Audi A4

1 Answer

Auxiliary belt tensioner replace


0197af1.jpg
A - crankshaft
B - alternator
D - power steering
E - belt tensioning damper
F - refrigerant compressor
G - tensioning roller
3 - ribbed V-belt 17,65 x 1432 mm. Partnumber: 038903137T
4 - ribbed V-belt 14,12 x 855 mm. Partnumber: 038260849

Please Rate my Response !
Thanks !

Jul 07, 2009 | 2004 Audi A4

1 Answer

1998 Jeep Grand Cherokee - Multi-rib belt Removal & Replacement


Check on upper rad shroud or under hood for routing diagram. Depending on what engine, procedure may vary a little. I wouldn't panic on replacing anything other than belt unless you noticed something noisy under hood in last while.
If not up to it, a mechanic should be able to do it for you in a few minutes usually, but won't hurt to ask before, just in case.

Jun 27, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Replaced belt tensioner and now the belt is to long


Your complete post does not display. So, I can only assume the rest says your belt is to big or to small. No matter what the case may be you have routed the belt incorrectly on the pulleys. If the tensioner is the same then the belt could not change the length. Rember, the outside smooth side of the serpentine belt rides on the smooth pulley surface and the ribbed pulley rides on the ribbed side of the belt. Look on the radiator cowl or the bottom side of the hood and it should have a routing schematic for you to follow. If it is gone just follow the smooth or ribbed formula above. Good luck.

Mar 12, 2009 | 2001 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...