Question about Cars & Trucks

1 Answer

Location of 91 olds 98 crankshaft position sensor

Where is it exactly in the car?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 74,251 Answers

Hello
See thiese videos.

Posted on Feb 13, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: Crankshaft Position Sensor location 04 PT Cruiser

It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Posted on Feb 08, 2009

  • 383 Answers

SOURCE: CANNOT FIND THE CRANKSHAFT POSITION SENSOR

cerebral_eni: The crank position sensor is located at the back of the engine block just below the cylinder head. It actually projects into the bell housing and reads the teeth on the flywheel where it references TDC for #1 cyl and RPM's of the crank. It's a "Hall effects generator". Unless you are into electronics and have a lab scope to look for a square wave pattern, I will continue with my other input.
Nissan has a recall campaign on the crank angle sensors.
The campaign # is 07V527000:ECM update for stalling;
NHTSA07V527000 NOV 07,
The symptom was brief malfunction of sensor causing the engine to quit running which could potentially put the vehicle at risk for a collision. The sensors would ultimately fail. There was also a voluntary recall on the reprogramming of the ECM's due to stalling problems. TSB# NTB07-081, Campaign ID#R0712
I hope this information is of some assistance to you. You may be able you get your car repaired under warranty! Good Luck!

Posted on Apr 08, 2009

emissionwiz
  • 76164 Answers

SOURCE: crankshaft position sensor location for a 98 lincoln towncar

it is on the front of the engine down low, here is a picture.
bfdacb9.jpg

Posted on May 11, 2009

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

on the engine where is the camshaft position sensor located

Posted on May 17, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankshaft position sensor on and olds 98


Should be behind the crank pulley under the water pump.

Jun 10, 2013 | Cars & Trucks

1 Answer

Were is the crank position sensor located on a 98 accord lx 2.2 motor?


There is no 2.2L motor in a 1998 Honda Accord.
The Crankshaft Position Sensor for the 2.3L 4-Cyl. engine is located behind the crankshaft pulley on the oil pump assembly.

May 10, 2011 | 1998 Honda Accord

1 Answer

Need to replace the crankshaft position sensor


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

  8. Unplug the sensor electrical connector.
  9. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  10. For 1992-99 vehicles, remove the sensor from the block face. To install:
    1. For 1987-91 vehicles, perform the following:
    2. Loosely install the crankshaft sensor on the pedestal.
    3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
    4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
      Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

    5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
    6. Remove the special tool.
    7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  11. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76°rotation.
  14. Install the inner fender shield and the right tire and wheel assembly.
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1999 Oldsmobile 88

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

2 Answers

98 silverado 5.7L camshaft position sensor


ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Oct 23, 2009 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

Where's the crankshaft position sensor located in 98 plymouth voy


Guessing it's a 6 cyl, 3.0L, but should be located on transaxle housing above vehicle speed sensor.c937fe4.jpg

Aug 31, 2009 | 1998 Plymouth Voyager

1 Answer

2000 Nissan Sentra Crankshaft Position and Replacement


Go to dealership they will give a diagram to locate every single one. I replace them on my daughter car. I believe there were three sensors. I exactly know what you are talking about. I had a hard time locating the back one right above the drive shaft on driver side.

Aug 27, 2009 | 2000 Nissan Sentra

1 Answer

Cant find the cam sensor


The camshaft sensor on this engine was located on the passenger side of the engine. You will need to remove the serpentine belt, and you can get to it by removing the inner fender or splash guard and get to it that way. I went down from the top. There are two sensors, one is a CRANKSHAFT sensor and other is a cam sensor. Make sure you know which is which. The crankshaft sensor is at the bottom of the engine, the camshaft is right by the water inlet. It is held in by 1 or 2 bolts. the camshaft sensor is not too hard to replace, it's tight but it can be done. unbolt the old and bolt in the new. Make sure you disconnect battery before tackling this project.

Apr 29, 2009 | 1991 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...