Question about 2002 Buick Rendezvous

Open Question

How to change license plate bulbs for 2002 buick rendenvous

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bunnydawg
  • 5158 Answers

SOURCE: Replacing Bulb for License Plate on 2001 Buick Park Avenue

Have you tried to see if there is access underneath to that bulb ?

Posted on Jan 17, 2009

  • 840 Answers

SOURCE: How to change the rear lights on a 2003 Buick Century.

yes you will you will have to take side trims and sill panel off get a 10 mm ready and take the bolts out the tail liaghts should come out the license lamps have screws in them and if you looka t them but you should be able to twist bulbs and pull them out / Please rate my response thank you very much

Posted on Jan 30, 2009

  • 6982 Answers

SOURCE: license plates light

check light socket grounding...repair as necessary Check power at hot side of light socket with a test light, grounded on a clean unpainted part of chassis. If light lights, then check ground side of socket.

Posted on Feb 15, 2009

  • 196 Answers

SOURCE: 2000 Buick Lesabre custom liscense plate bulb

kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Posted on Mar 20, 2010

tecnovative
  • 360 Answers

SOURCE: License plate bulb replacement on a 2002 Buick

Hi, my name is John I will do my best to assist you.

The entire tail/backup lens assembly has to be removed from the trunk lid as shown in the drawing attached. There will most likely be some nut's or clip's on the assemblies mounting pins on the inside of the trunk lid.

  1. Disconnect the tail/back up lamp harness connector from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.
  5. Installation is the reverse of removal.

tecnovative_128.gif
If you have more specific questions please post comments to this thread and I will endeavor to monitor new activity and respond as soon as possible. I recommend that you "bookmark", or "add to favorites" this page for your convenience.

Posted on Feb 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change rear license plate bulb


To gain access to license plate bulbs you have to remove the center tail lamp off the trunk lid.

Dec 14, 2015 | 2005 Buick Rainier

1 Answer

Change license plate bulbs in 2004 buick lesabre custom


  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.

Sep 22, 2014 | 2004 Buick LeSabre

2 Answers

Change the license plate lights in my 2002 buick rendezvous cx


On most GM cars, SUV's, and light duty trucks, the license plate light bulbs are held in place by 2 screws...located on each side of the plastic lens...remove these 2 screws then wiggle the entire assembly out so you can view and replace the bulbs...Again most GM cars have 2 bulbs also...Hope this helps.

Sep 06, 2013 | 2002 Buick Rendezvous

1 Answer

How do you change a light bulb above the license plate in a 1989 buick park avenue


How do you change a light bulb above the license Problem with the 1989 Buick Park Avenue

Oct 08, 2010 | 1989 Buick Park Avenue

1 Answer

How to replace license plate light on a 2002 buick lesabre


Hi. Remove the retaining screws from the license plate light assembly with a Phillips screwdriver. There are two screws on each side of the lens assembly.

Pull the light assembly cover down out of the way to gain access to the bulbs. Twist the bulb socket counterclockwise to remove it from the assembly and pull it straight out. Pull the bulb out of the socket.

Push the new bulb straight into the socket. Replace the bulb and socket inside the light assembly and turn it clockwise to secure it.

Replace the assembly cover and secure it with the retaining screws. Tighten the screws with a Phillips screwdriver. Turn on the lights to test your new bulbs.
Take care

Aug 04, 2010 | 2002 Buick LeSabre

2 Answers

How can I replace the license plate lights?


mcdevito75 here, Just above the license plate in the bumper you should see the light lens, simply remove the 2 screws and change the bulb/bulbs

Jun 18, 2010 | 2002 Buick LeSabre

1 Answer

How do I replace license light bulbs in my 1995


I have a 2002 which is a little different body style but it may be the same process. You have to take the back plastic section that holds the license plate loose from the car. There are bolts that are inside the trunk that hold the plastic panel on. Mine are in the trunk lid. If your plastic panel, license plate, etc. goes up with the trunk lid they are in the lid. You need deep type sockets to reach the nuts, at least mine does.

Mar 31, 2010 | 1995 Buick LeSabre

1 Answer

2000 Buick Lesabre custom liscense plate bulb


kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Mar 08, 2010 | 2000 Buick LeSabre

1 Answer

Troubles removing license plate light bulb


yes,thats the only way sorry to say.

Mar 02, 2009 | 2002 Buick Regal

1 Answer

2002 license plate bulbs


its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Feb 01, 2009 | 2002 Toyota Avalon

Not finding what you are looking for?
2002 Buick Rendezvous Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...