Question about 1988 Chevrolet S-10

1 Answer

Changing tps on 89 s10 with 4.3 - 1988 Chevrolet S-10

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Expert
  • 1,868 Answers

Hello! On most applications, it will be necessary to rotate the sensor counterclockwise to align the bolt holes...Guru...saailer



ACDELCO Part # 2133859




Changing tps on 89 s10 with 4.3 - 2_13_2012_12_25_30_am.jpg

Posted on Feb 13, 2012

  • zernie miller-frost
    zernie miller-frost Apr 30, 2014

    so does this mean the lever on the back side goes to the left side of the throttle or the right side on the throttle body?

  • David Burbee
    David Burbee Apr 30, 2014

    Make sure the throttle valve is closed, then position the sensor over the shaft and rotate the sensor counterclockwise to align the bolt holes...You will feel tension when turning the TPS ccw, this indicates it is correctly positioned...saailer

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 91 Answers

SOURCE: 1989 s10

not sure on the book procedure, but on my 91 4x4 extended cab I had to undo the u joint caps on both ends, then colapse the shaft as short as it will go by pushing back the slip yoke. Then you need to move the front of the shaft in by the trans and as far forward as you can. it will be right along side the yoke you unbolted it from and the u joint has to be turned just right for maximum room, but this should give you enough room to force the tail of the shaft pass the crossmember. Its very tight.

Posted on Mar 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why My 89 pu toyota run better w/o the tps sensor


I believe that the TSP on your Toyota is adjustable. Follow the manufacturer recommendations to adjust the position of your TPS, and MAKE SURE YOU PUT THE RIGHT TPS ON THE VEHICLE.

Jul 18, 2014 | 1989 Toyota Pickup SR5

2 Answers

I have an 89 ford f150 that is stalling randomly after replacing the fuel pump. its showing codes 34,44.


Code 34- EVP voltage a Code 44- Thermactor air system inoperative-right sidebove closed limit

Sep 03, 2012 | Ford F-150 Cars & Trucks

1 Answer

My 89 Seville STS started to idle high sometimes but not all the time. Now it seems to be doing it mostly all the time. I just replaced the ISC myself with no change. Is there something else I can...


Yes, there is a procedure to get the engine to idle correctly. Turn engine off, key on Open the throttle and let in snap shut against the minimum air screw. The throttle angle displayed in diagnostics on ECM parameter ED01 TPS -1.0 to + 1.0. The TPS should be adjusted to fall into this parameter. After that has been done. Connect a wire from the -side of battery to terminal c on the isc motor. and a wire to the + side of battery to terminal d. The plunger should be at its highest position against the throttle lever to adjust. This may take a few times of applying power to get it to ratchet to full ext. The TPS parameter should be at 10.5 to 11.5 on the diagnostic center. Adjust by turning the plunger on the ISC. Press the cool blue button and the off button to get the diagnostic function up. Any more question please reply as I have a service manual and fixed my 89 seville for this problem.

Aug 21, 2011 | 1989 Cadillac Seville

1 Answer

Hello, my name is Tim. My uncle has a 89' Bronco ii. While cruising on flat, level highway, the transmission kicks in and out of overdrive. Do you have a suggestion? The transmission has been replaced,...


Durango would shift in and out of overdrive while driving at a steady rate. Replaced the throttle position sensor and fixed the problem. here are a few causes for a bad tps. transmission shift issues, bucking, jerking, idle surging, engine cutoff, hesitation on take off, surge while cruising down highway. have a good day ! tps is used by computer to monitor throttle position and adjust the speed, fuel and air to match throttle position. if tps is bad it will send wrong info. to computer. hope this helps !! if all else fails clean maf sensor. check tps first.

Jun 16, 2011 | Ford Bronco II Cars & Trucks

2 Answers

Code p0122 and p0123 after changing computer


Hi.

The problem is regarding TPS (throttle position sensor located in throttle body). Both codes are TPS voltage out of range (low and high) If you get both codes at once, then :

TPS may be defective,
wiring to TPS may be shorted to ground.
There may be a problem in the +5V circuit powering the TPS.
There may be a problem with ECU connector.

Jan 20, 2011 | 1996 Dodge Caravan

1 Answer

My 89 4.0 A/T 4wd cherokee gets to 20mph then bogs down


What are the RPMs at when it's at 20 MPH?
I would personally start listening for vacuum leaks. That's a quick easy fix.
The 89 is notorious for problems with the TPS sensor (throttle position sensor) and the idle air control valve thos are also cheap easy fixes.
What do you mean by bog down is there any shuddering involved?
Shuddering this could point to a short on the engine block.

Jan 03, 2010 | 1989 Jeep Cherokee

1 Answer

Idles at 3100 rpm after changing tps


check for vacuum leak, could be power brake assist, high rpm indicates leak

Oct 26, 2009 | 1993 Oldsmobile Cutlass Ciera

1 Answer

89 z24 stalls instantly when shifting out of park


Your lockup torque converter is bad I believe. When you shift from Park into any gear it will die.

Sep 17, 2009 | 1989 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...