Question about 2000 Dodge Intrepid

Open Question

PICTURE OF A BELT TENSIONER FOR A 2000 DODGE INTREPID

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
RudolfDiesel
  • 100 Answers

SOURCE: replacement of belt tensioner

Hello
Welcome to FY,
Your tensioner is replaced as a unit,
remove the belt.
there is a nut 15mm that holds the tensioner to the engine, the tensioner and pulley comes off together the new one will have a pulley on it too, install the ne one the same as the old one came off. i would replace the belt too.
RD

Posted on Jan 12, 2009

Ad
t1randa
  • 27 Answers

SOURCE: Serpentine/drive belt routing diagram of a 2002 dodge Intrepid needed.

check dodge website you have to register to get the owners manual which has or if you have your owners manual

Posted on May 29, 2009

  • 112 Answers

SOURCE: Belt Tensioner replacement

A simple bolt on assembly, the tensioner for the serpentine belt may need replacement if it fails to smoothly pivot and maintain tension on the belt.

Using a half inch breaker bar, release tension by rotating against the spring, remove the belt from the tensioner. Unbolt the tensioner (one bolt may be so diffucult to reach that you might want to use a racheting open end wrench by Alden.
Install the new tensioner by reversing these steps.
I usually replace the belt at the same time.

Posted on Jul 02, 2009

bschilz
  • 2049 Answers

SOURCE: where is cabin air filter 2000 dodge intrepid

The 2000 Dodge Intrepid is not equipped with a cabin air filter.

Posted on Jan 19, 2010

  • 19 Answers

SOURCE: how does the timing chain tensioner work for a

On both sides of the chain, right above the crankshaft, there are two guides. The chain runs over these guides, the tenion is adjusted by moving one of the guides in more to press on the chain tighter.cebc361.gif

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just had trans rebuilt in my 2000 dodge intrepid 3.2 now there is noise from front of engine by belt rattling ?


Sounds like it could be the belt tensioner.These tensioners wear out over time i've had to replace a few of them.

Nov 02, 2012 | Dodge Cars & Trucks

1 Answer

The tensioner pully bracket broke to the alt/pwr steering belt. it made of cast aluminum. is this a replaceabe part? if not can it be welded? or fixed at all?


Yes it is a replaceable part. Just get the whole tensioner pulley assembly from the junkyard, its held on by 3 bolts and bolts into the timing cover.

Aug 14, 2011 | 2000 Dodge Intrepid

1 Answer

I need to know hw to get the tension of the ac belt on a dodge 2000 intrepede


While under the car, If you look up under the front of the engine from the passenger side you will see the tensioner pulley. Loosen the center nut on the pulley and then turn the bolt that adjusts tension counterclockwise to loosen.

Jul 19, 2011 | 2000 Dodge Intrepid

1 Answer

How to change a serpentine belt on a 1999 intrepid?? Does the alternator need to be loosened??


The alternator does not have to be loosened.

The tensioner mount has a square hole in it for inserting a ratchet or a breaker bar. Pull the tensioner in the direction which realeases the tension on the serpentine belt.

Charlie

Jan 08, 2011 | 1999 Dodge Intrepid

1 Answer

What is the timing diagram for a 2000 dodge intrepid 2.7 litre engine


Trying to time this 2000 intrepid 3.5L after puting water pump in i line the timeing mark But when i put the tensioner back on it throws the mark off

Jun 15, 2010 | 2000 Dodge Intrepid

1 Answer

How to replace tensioner pulley on 2000 Dodge Neon


Make sure you locate the Serpentine Belt Routing Sticker before you proceed. If not make an excellent drawing and take a GOOD Picture. Do NOT try to just remember how it goes back on Should be a 15mm wrench to loosen tensioner to remove belt. Locate mounting bolts to tensioner and remove, replace with NEW tensioner tighten bolts then use wrench arc torque about 15 degrees should snug it down, reroute belt then using 15mm pull tensioner to either side of belt to install belt in correct route. Remove all tools and body parts from engine bay. Do not start engine if anyone is in the vicinity of engine bay. Belt may fly off if you did not do it right and cause all kinds of shrapnell, if it doesn't fly off, visually inspect belt before starting and after, I would suggest being very careful before during and after starting to insure safety.

Jan 05, 2010 | 2000 Dodge Neon

1 Answer

I can't get the power steering belt back on because of the tentioner


Does the tensioner have a bolt on it? Put a socket wrench with a long handle on this bolt and try to push the tensioner to one side. This should give you enough room to get the belt in place.

Oct 18, 2009 | 2000 Dodge Intrepid

1 Answer

How do I remove the alternator on a 1999 Intrepid with a 2.7L engine


remove belt from pulleys use a wrench on the tensioner to get belt off then remove mounting bolts on alternator should be a diagram of pulleys under the hood to tell you where the tensioner is

Sep 29, 2009 | 1999 Dodge Intrepid

1 Answer

The front belt, toward radiator, does not have a tensioner. How do I change it. 2001 Dodge Intrepid, 2.7 ltr.


IT DOES HAVE A TENSIONER PULLEY..SMALLER PULLEY LOCATED TO THE LEFT OF P/S PUMP..LOOSEN NUT ON FRONT OF PULLEY(15MM WRENCH)..AND THERE IS A BOLT LOCATED JUST BEHIND PULLEY(13MM SOCKET)LOOSEN THIS AND REMOVE BELT..IT IS EASIER TO REPLACE BELTS WITH UPPER RAD SUPPORT REMOVED..I HOPE THIS HELPS

Aug 26, 2009 | 2001 Dodge Intrepid

Not finding what you are looking for?
2000 Dodge Intrepid Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...