Question about 1991 Plymouth Sundance

Open Question

1991 plymouth sundance diagnostic codes

Cranks but won't start

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 49 Answers

SOURCE: have codes coming up on

Do you know the codes or are you asking for help pulling the codes?  If you know the codes, go here to find out what they mean.  If you need to pull the codes, most auto parts stores will pull the codes for you for free.

Posted on Jan 25, 2009

Ad
  • 124 Answers

SOURCE: Replacing the heater core on a '88 Plymouth Sundance?

Behind the dash. You will have to pull the whole dash assembly. It looks like a little radiator.

Posted on Mar 28, 2009

  • 104 Answers

SOURCE: 1993 Plymouth Sundance will not start or turn

Make sure battery is fully charged. Connect a test light to battery ground and touch batt+ to check if light. Now test that there is power to the starter heavy wire directly connected to the starter. If power, good. Now test for cranking power to solenoid wire which is on top of starter; have someone cranks as you check for power. If there is power, starter could be acting up. If not, check all fuses and neutral switch. Be careful working around moving and hot parts.

Posted on Jun 12, 2009

emissionwiz
  • 76070 Answers

SOURCE: i need all the engine diagnostic codes for a 94

11 Timing belt2.gif skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM/ECM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failur

Posted on Aug 08, 2009

  • 14585 Answers

SOURCE: 1993 Plymouth Sundance 2.2L cranks, no start

When you turn the ignition on the pump is energized for 2 to 3 seconds. did you check it like that. it is also energized when cranking the engine. there is a fuse then a relay then the fuel pump. the relay is ran/ energized by the ecm computer. if there is a fuse relay box under the hood you'll need to check there to. good luck

Posted on Jun 17, 2010

Testimonial: "This was incredibly helpful. I couldn't find the information you got for me and I was searching everywhere. Thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankes but won't start


run fault codes and check for cam/crank position sensor problem/ Check that the camshaft is turning ( broken timing belt/chain) check operation of the immobiliser

Mar 18, 2014 | 1991 Plymouth Sundance

1 Answer

How do u reset codes on a 1991 plymouth sundance


Disconnect the battery for a couple minutes

If you have problems, don't clear,a shop will
need the data stored to diagnose

Oct 03, 2012 | 1991 Plymouth Sundance

1 Answer

What code 44 on a plymouth sundance 1991


Generally speaking, code 12 means the battery has been disconnected at some point in time.
Code 44 means the battery temp sensor circuit is out of normal range, too high or too low.

Oct 03, 2012 | 1988 Plymouth Sundance

1 Answer

92 plymouth sundance. loud pop on drivers side when turning. steering wheel won't turn when brake is pressed.


thats your axle its bad or you call it cvc joint needs to be replace it cost about $150

Apr 26, 2012 | 1992 Plymouth Sundance

2 Answers

When trying to start my 1991 Plymouth Sundance America I hear only a clicking sound. I replaced the battery but it did not work. Can it be the alternator?


sounds like you have a bad starter.not your alternator.if the battery is good the car should start even if the alternator is bad.you can even drive the car until the battery runs low.the alternator job is to keep the battery charged.soulds like the solinoid is clicking.but no responce from the starter.have starter checked.

Dec 08, 2010 | 1991 Plymouth Sundance

2 Answers

Where is te starter on a 1991 plymouth sundance what is it hooked


The starter is located on the bottom of the engine, where the engine and transmission meet. It is on the side of the engine closest to the front of the car. The easiest way to find it is to follow the positive battery cable, as it goes directly from the battery to the starter solenoid.

Jan 22, 2010 | 1991 Plymouth Sundance

1 Answer

Where is the staretr located on an 1991 plymouth


On the side of the engine block above the oil pan faceing the transmission.

Jan 21, 2010 | 1987 Plymouth Sundance

1 Answer

How to fix emergency brake on 1991 plymouth sundance. when i push down all the way the brake light in the dash comes on but the car doesnt stop


There is a wire split under the car on driver side,but follow the wire and you should run into the prob.

Oct 27, 2009 | 1991 Plymouth Sundance

1 Answer

Intermittant loss of acceleration on my 1991 plymouth sundance


Turn key, on, off, on, off, on & leave it on (not start) & count check engine flashes. 2 digit codes, for example: flash, flash, flash, pause, flash,flash., is code 32

Mar 29, 2009 | 1991 Plymouth Sundance

Not finding what you are looking for?
1991 Plymouth Sundance Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...