Question about 2008 Mercury Grand Marquis

1 Answer

My car didnot start engine

Also ni light

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 430 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

The oil light comes on, but there is plenty of oil


well you have two things to check first to replace the oil presure switch and the check for the wire sometime the switch start leaking on the wire. if this didnot fix the problem then you need to check the oil pressure if this is didnot pass then you have an internal eng problem

Jul 21, 2009 | 1987 Chevrolet Cavalier 4 Door

1 Answer

Cant get my distributor installed correctly in 1994 gmc 1500 has a 350 in it?


if you didnot mark rotor orientation before removing pyt engine on top dead center # 1 cyl line roter up to #1 plugwire post on dist cap with a light look down the shaft bore for a slot that matches the end of dist shaft if they do not match p[osition get a long screw driver an turn the shaft in engine until they do then drop dist you may have to turn the rotor backwards about a tooth when you start to drop whn the cam and dist gears mesh it will line up oil pump drive shaft to dist shaft

Mar 30, 2012 | 1994 GMC Sierra

1 Answer

My car didnot start yesterday afternoon , nexttday moning it was started today afternoon it was not start again. the starter is working , but engine donot working


Three component that need to be available for the vehicle to start fuel (you need the right pressure) Spark the ignition must be able to ignite the sparkplugs, Air you need a proper ratio to maintain idle. You can be looking for a distributor, or a fuel pump

Mar 02, 2012 | 1994 Plymouth Voyager

1 Answer

Trouble code 41: my car was stalling all the time, and after a while would not start, (didnot turn over), or start and the die immediatly, so I replaced the cam shaft sensor, like it said.in the chilton...


Cam sensor signal was not received by PCM for the last 2 seconds while engine was running. You may have a bad crank sensor and balancer that is coming apart.

Dec 05, 2010 | 1990 Buick LeSabre

1 Answer

I get a 12 code but didnot have battery 94 jeep


check and clean battery posts and clamps. if light is on after cleaning battery. have it turned off with a scanner.

Feb 13, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Wont start so i change timing chain it turn over but didnot start step on gas and turn over and it want to start but not


what engine???? was there a problem with the chain? you need a shop to check out whats bad, you dont want to spend anymore money without knowing whats wrong.

Oct 01, 2009 | 1995 Pontiac Grand Am

1 Answer

Nissan Altima 2004 SES light and some times engine donot start


its going to be between the motor and tran on the back lower part it is going to be in between a small gap i chande it on my friends car and it work

Aug 24, 2009 | 2005 Nissan Altima

1 Answer

After purchasing a flood 2006clk 500 i made anew rebuilding for the engine and its okk but it didnot start may be need computer for reset or any control unit need to be changed thanks


hello,your engine is cranking but not starting,since your unit is flooded,your fuel pump is working?pls. check your fuel pressure,maybe some electrical connection have poor contact,or during starting cluster appear 'start error' this message need to check with computer(star diagnose)ty

Apr 26, 2009 | 2006 Mercedes-Benz CLK 500

1 Answer

My engine would not start


What is this?uuuuuuuuuu

Jan 02, 2009 | 2006 Kia Sorento

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...