Question about Toyota Highlander

1 Answer

Rattle in front end - suspect axle pivot bushings

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

Yes it is probably your bushings

Posted on Feb 12, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1952 chevy truck king pins install


Remove the road wheels, remove front hub from stub axles, remove the cotter pin nut and drive out the pin, remove the welch plug on the top of the king pin and with a drift drive the pin through the axle, press the old bushes from the stub axle and press in new bushes, ream the bushes till the king pin will just slide in .Then assemble make sure there is no play between the pivot bearing and stub axle use shims if required.

Sep 24, 2014 | Cars & Trucks

2 Answers

Hi I have a rattling sound coming from my landrover freelander and the suspension feels no good at all the little humps in the road feel like they are a lot larger than they are but my question is is


LOL Check the bushes of the torque tension bar saddles. Either they are loose or the bushes are shot. The are located on the front axle and the saddles is fastened down on the cross member.

Jun 12, 2013 | Land Rover Freelander Cars & Trucks

1 Answer

Jaguar xtype front rattle when hitting pothole sounds like comes from both sides.. might it be shocks ?/ 150.000 km on clock


More likely cause are control arm bushings or tie rod ends, or ball joints. Drag link bushings can also be at issue. If you are handy, get a very large pair of channel lock pliers and locate every suspension mounting point you can find that has a dust boot and connects to a suspension part. These are usually ball shaped things with a stud that passes through another part and is secured with a large nut and cotter pin. If you carefully clamp the part with the pliers--such as tie rod ends--so as not to damage the dust boot, you may find it has some free play. If so, that may be the culprit. Any free play in any of your suspension parts could be the problem. You mentioned shocks...the top of the shock absorber strut has bushings which sometimes do wear out, but based on your description, it sounds like a worn suspension bushing or pivot point.

May 02, 2012 | Jaguar X-Type Cars & Trucks

2 Answers

When going over bumps it moves all over the road. Front end goes all over the road. at 60 mph the car shakes an moderate oil leak.


These sounds like something is going on underneath the front of your subaru. The usual suspects will be the arm controls, stabilizers even axles, let a mechanic look at it, sounds dangerous. thank you!

Mar 10, 2011 | 1997 Subaru Impreza

2 Answers

I have a 1997 Jeep Grand Cherokee, Im getting a rattle under the jeep. It sounds like metal hitting metal its not the exhaust for that is not hittig anything. it sounds like its to the rear. Someone said...


Your jeep has two upper and two lower control arms attached to the rear axle. They have rubber bushings where they bolt to the axle and to the body. If the bushings are badly deteriorated, you will get a metal to metal sound when hitting bumps. Have them all checked.

Jan 03, 2011 | 1997 Jeep Grand Cherokee

1 Answer

On my 2002 Sebring LXi 2.7L there are so many rattles and noises when I go over any size bumps. Had front top strut bushings replaced, but did not help.


Need to check the entire front end at a place like Sears or your dealership to determine what parts have excessive play in them. Sears doesn't usually charge for this service, in hopes that you would have them work on the car in the future.

Sometimes, the cv joints are worn and cause a rattle or clicking on turns. Also, the bushings for the lower control arms sometimes wear out causing a rattle or other noise that can be disconcerting.

When the strut bushings were replaced, were the other parts in the front end checked out?

Good luck on this repair.

Nov 06, 2010 | 2002 Chrysler Sebring

3 Answers

Rattle on front end - especially when hit bumps. Is this struts? How dangerous is the problem?


A rattle in the front end is a pretty vague description. This could be caused by struts, loose mounts, loose wheels, engine mounts or almost anything else but may I suggest you check the sway bar bushes located at the end of the sway bar, this is the most common cause of rattles in these vehicles. I also suggest you check every other bolt you can see in the front end, then look for more and check those too. Every rattle has potential to be dangerous, especially suspension faults, I suggest that you take your car to a competent mechanic as anything you touch in relation to suspension could kill you or someone else, I have seen it happen. I hope this helps and good luck.

Aug 10, 2010 | 2003 Toyota Highlander

1 Answer

Rattling noise from near side front wheel area. Have checked for play on bearing and checked brake disc. No problem detected. Noise only occurs at low speeds.


i have the exact same problem ive got 2001 honda civic and have an annoying rattle from the wheel area. i have replaced cv joint, ball joint, sway bar drop links, strut, and suspension bushing and arm....but still rattle noise is there. dnt have a clue what it could be, from looking on the internet i have found few possibilities.....lower control arm/bushin...motor mounts....gear box mounts....strut rod bushing....axle....inner/outer cv joint....calliper pins......shock/shock bushing...or wheel bearing. im hoping tio get all this checked out its got to be able to be fixed somehow!

Dec 29, 2009 | 1997 Volkswagen Golf

1 Answer

Front end alignment 1987 ford bronco


That is a camber problem. most likely Axle Pivot Bushings, or lower ball joints.

May 21, 2009 | 1987 Ford Bronco

1 Answer

2000 Explorer Clunks, sounds "loose" suspension


it sounds like the radis arm bushing are wore out they are the arms that go between the frt. axle to the frame they have round bushings that are bolted the the frame rails just behind the frt tires.

Mar 04, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...